Sony UP-GR700 - Manual (Page 22)

Mi
sc
el
lane
ou
s
Specifications / List of Messages
22
Specifications
Power requirements
100 to 240 V AC, 50/60 Hz
Input current 3 A to 1.3 A max. (while printing)
Operating temperature range
5°C to 35°C (35°F to 95°F)
Operating humidity range
20 % to 80 %
External dimensions
Approx. 370 Ч 350 Ч 400 mm (WHD)
(14 5/8 Ч 13 7/8 Ч 15 3/4 inches)
(including the maximum projecting
parts)
Mass Approx. 30 kg (66 lb 2 oz) (printer
only)
Printing system Dye sublimation thermal transfer
Thermal head
11.8 dot/mm, 2560 elements (300 dpi)
Gradations 8 bits each for yellow, magenta and
cyan
Picture size 203 × 254 mm (8 × 10 inches)
203 × 305 mm (8 × 12 inches)
Printable pixels 2444 × 3044 dots (for printouts of 203
× 254 mm size (8 × 10 inch size))
2444 × 3644 dots (for printouts of 203
× 305 mm size (8 × 12 inch size))
Printing time Glossy laminating type:
203 × 254 mm size (8 × 10 inch size);
Approx. 43 sec.
203 × 305 mm size (8 × 12 inch size);
Approx. 48 sec.
Matt laminating type:
203 × 254 mm size (8 × 10 inch size);
Approx. 53 sec.
203 × 305 mm size (8 × 12 inch size);
Approx. 58 sec.
Input connector AC IN (for power)
Interface
Hi-Speed USB (USB2.0)
Accessories supplied
Feet (2)
CD-ROM (1)
Software License Agreement (1)
Before Using this Printer (1)
Warranty Card (1)
Optional accessories
Self-Laminating Color Printing Pack
2UPC-R710 series
Air Filter
Design and specifications are subject to change without
notice.
List of Messages
Error numbers and error messages appear on the monitor
of the computer connected to the printer. Please take the
remedial actions shown next to the message to correct
the problem.
Error numbers and error messages
requiring the printer to be turned off and
on
When the following error numbers and error messages
appear on the monitor, you should turn the printer off.
Please take the remedial actions shown next to the
message to correct the problem. Then turn the printer on
again. If the error message and the error number are still
displayed, and the problem has not been solved, contact
your nearest dealer.
Message Description and Remedy
E00 USB Communication Error.
Please Check USB Communication.
E01 Print head does not work. (up).
Please re-start the printer.
E02 Print head does not work. (down).
Please re-start the printer.
E03 Please check the position of the ink
ribbon and re-start the printer.
E04 Error in head controller.
Please re-start the printer.
E05 Paper jam during feeding
Please re-start the printer.
E06 Paper jam during rewinding.
Please re-start the printer.
E07 Paper cutter is not working.
Please re-start the printer.
E08 Internal command error.
Please re-start the printer.
E09 Error in writing flash ROM.
Please re-start the printer.
E10 Failure in power supply.
Please re-start the printer.
E11 Failure in grip roller movement.
Please re-start the printer.
E12 Please check the room-temperature
thermostat.
Please re-start the printer.
E13 Please check the room-temperature
thermostat.
Please re-start the printer.
E14 Please check the print-head thermostat.
Please re-start the printer.
E15 Please check the print-head thermostat.
Please re-start the printer