Sonance ST2432D Series - Manual (Page 2)

Performance Specifications:
Radiating Surface: 549 in 2 (3,540cm 2 ) Planar Diaphragm
Tweeter System: 0.82 lb (0.37kg) Magnet with 1.02” (26mm) voice
coil; 1,200Hz, 12dB/octave high-pass crossover
Woofer System: 0.82 lb (0.37kg) Magnet with 1.02” (26mm) voice
coil; 1,200Hz, 12dB/octave low-pass crossover
Frequency Response: 40Hz – 19kHz ±4dB
Power Rating: 75 Watts RMS as per EIA standard RS-426-A
Pressure Sensitivity: 92dB, 1W/1m
System Impedance: 8 ohms nominal, 5.5 ohms minimum
Transformer: Primary Voltage — 70.7 Volts
Primary Taps — 0.5, 1, 2, 4, 8, 16, 32 Watts;
8-ohm bypass
Dimensions (H x W x D): 23 7 /
16
” x 23 7 /
16
” x 3” (595mm x 595mm x 76mm)
Product Weight: 11.0 lbs (5kg) each
Shipping Weight: 15.5 lbs (7kg) each
212 Avenida Fabricante
San Clemente, CA 92672
(800) 592-4644 • (949) 492-5449
FAX: (949) 361-5151
www.soundadvance.com
Architects and Engineers Specification:
The ST2432D SpeakerTile ® shall be a dual-driver, two-way, full-range device,
producing frequencies from 40Hz to 19kHz in both horizontal and vertical
planes. The SpeakerTile shall have a sensitivity of 92dB (1W/1m), with a rated
power of 75 watts RMS according to EIA standard RS-426-A.
The total radiating surface area shall be 549 in
2 (3,540cm 2 ). The high-
frequency dispersion shall be at least 140° to the upper frequency limit of the
device in question, in both horizontal and vertical planes.
All SpeakerTile models shall have an exterior frame constructed of extruded
aluminum that is 23 7 /
16
” (595mm) in length, 23 7 /
16
” (595mm) in width, and 3”
(76mm) in total unit depth, not including backbox. The complete unit shall
weigh not more than 11.0 lbs (5kg) without its mounting accessories.
The loudspeaker shall be the Sound Advance ST2432D or equivalent.
Polar Response:
ST2432D Series
24” x 24” Hemispherically-Radiating SpeakerTile
®
©2006 Sound Advance. All Rights Reserved.
Sound Advance, SpeakerTile and Planar Diaphragm Technology are trademarks or registered trademarks of Dana Innovations.
Specifications subject to change without notice. For the latest Sound Advance product information please go to
www.soundadvance.com 05/06
500Hz
300°
330°
0°
30°
60°
270°
50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB 1kHz
300°
330°
0°
30°
60°
270°
50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB
2kHz
300°
330°
0°
30°
60°
270°
50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB
500Hz
1kHz
2kHz
4kHz
300°
330°
0°
30°
60°
270° 50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB
8kHz
300°
330°
0°
30°
60°
270°
50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB 16kHz
300°
330°
0°
30°
60°
270°
50dB 40dB 30dB 20dB 10dB 0dB 90° 50dB 40dB 30dB 20dB 10dB 0dB
4kHz
8kHz 16kHz
dB
25 50
40
30
20
10
0
kHz 20 210 5 200 500 1 Hz 100 50 20
0
10
20
30
40
50
dB
Warranty:
Sound Advance warrantees the ST2432D to be free of any defect in materials
or workmanship for a period of 5 years from the date of purchase. During the
warranty period, Sound Advance will repair or replace (at its option) all such
defects without charge for parts or labor, if returned prepaid to the proper
Sound Advance service facility, together with the original sales receipt or other
proof of purchase. The unit will be returned prepaid.
ST2432D
SpeakerTile
PBB 2.0
Backbox
Ceiling Tile
(used as rear
panel of backbox)
T-Bar
Ceiling
Grid
Installation Example:
On-Axis
Frequency
Response: