JVC LVT1007-010A[A] - Manual (Page 37)

35
Activating the Surround Modes
Available Surround modes vary depending on the speaker settings
and the incoming signals. (See page 32.)
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 23 to
31.)
You can also use the buttons on the remote control for the same
functions.
Activating the EX/ES setting
For multi-channel digital software, you can activate the EX/ES (7.1-
channel) reproduction mode.
• Once you have set EX/ES (7.1-channel) reproduction mode, it is
stored in memory and will be called up whenever you activate the
Surround mode which the memorized EX/ES (7.1-channel)
reproduction mode can be applied to.
Press EX/ES to select an appropriate setting for your enjoyment.
The currently selected EX/ES (7.1-channel) reproduction mode
appears on the display.
• Each time you press the button, it changes as follows:
EX/ES AUTO*: According to the incoming signal, an
appropriate Surround mode is applied.
• For Dolby Digital EX and DTS-ES,
EX/ES (7.1-channel) reproduction is
applied.
• For 5.1-channel (or less) encoded
software, 5.1-channel reproduction is
applied.
EX/ES ON*: Select to apply EX/ES (7.1-channel)
reproduction to both 5.1-channel and 6.1-
channel encoded software.
EX/ES OFF: Select to cancel the EX/ES (7.1-channel)
reproduction.
* If the surround back speakers are not connected or deactivated,
Virtual 6.1-channel surround is applied.
Notes:
• When Surround mode is deactivated, pressing EX/ES will
activate an appropriate Surround mode for the current source.
• When an analog or digital 2-channel source is playing, you can
adjust the EX/ES (7.1-channel) reproduction mode and store
the setting, but it will not affect the current source.
• When the source is one to which the EX/ES (7.1-channel)
reproduction cannot be applied, you can adjust the setting and
store in memory, but reproduction channels will remain
unchanged.
Activating the Surround Modes
1. Select and play any source other than “DVD
MULTI.”
• Make sure you have selected the analog or digital input mode.
• Surround modes are not valid for DVD MULTI playback
mode.
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software (except 2-channel and
Dual Mono software), incoming signals are automatically
detected and the appropriate surround mode is activated (see
page 34 for details).
– If the EX/ES (7.1-channel) reproduction mode has been set
to “AUTO” or “ON,” one of the EX/ES (7.1-channel)
reproduction modes will be activated (see the left column).
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, Surround modes change as follows:
• For Dual Mono software, you can select the channel you
listen to. (See page 27.)
To adjust the speaker output level, see pages 30 and 31.
To cancel the Surround mode
Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote
control). “SURR OFF” appears on the display.
Ex. When “DOLBY D” is activated.
VOLUME
LINEAR PCM
DIGITAL
L
SUBWFR
LS RS
C R
LFE
DIGITAL AUTO
SPEAKERS 1
VOLUME
LINEAR PCM
DIGITAL
L
SUBWFR
DUAL DIGITAL AUTO
SPEAKERS 1
VOLUME
LINEAR PCM L
SUBWFR
R
ANALOG
PRO LOGIC
SPEAKERS 1
NEO:6CINMA NEO:6MUSIC
PL II MOVIE PL II MUSIC PRO LOGIC
RX-7032V AUDIO/VIDEO CONTROL RECEIVER
RX-7032V AUDIO/VIDEO CONTROL RECEIVER
32-38_87032[A]3.pm6 03.5.12, 7:02 PM 35