JVC DR-MV5S - Manual (Page 31)

Masterpage:Right0
EN
31
Filename [MV5S_08Basic TimerDub.fm]
Page 31Tuesday, 8 March 2005 19:32
TIMER RECORDING
You can program each deck to timer-record as many as
8 programs up to 30 days ahead.
With the VCR Plus+ system, timer programing is greatly simplified
because each TV program has a corresponding code number
which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
NOTES:
● There may be cases that the VCR Plus+ Timer Programing function
prolongs the stop time of the programing.
● When two successive programs are recorded on a DVD-RW disc with
the VCR Plus+ Timer Programing function, the beginning of the
second one may be left off the recording.
● VCR Plus+ Timer Programing is not possible on the discs used
exclusively for On-Disc Timer Programing.
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
● To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to “Cable Box and DBS
Receiver Users (DVD Deck Only)” above.
1
Press DVD or VHS to select the deck on which you want to
perform timer programing.
2
For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3
Press VCR Plus+ to access the VCR Plus+ screen.
4
Press the number buttons to
enter the PlusCode number of a
program you wish to record, then
press ENTER.
● If you have made a mistake, press
CANCEL and input the correct
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR (8).
● If the number you entered is
invalid, “PLUSCODE NO. ERROR CONFIRM PLUSCODE NO.
THEN RETRY” appears on the TV screen. Input a valid PlusCode
number.
● If “GUIDE PROGRAM IS NOT SET” appears on the TV screen, set
Guide Channel numbers manually. (
੬ pg. 77)
● When “PROGRAM FULL DELETE UNWANTED TIMER PROGRAM”
appears on the TV screen, you need to cancel some of the reserved
programs. (
੬ pg. 35)
5
The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
program data.
● To cancel this setting, press RETURN.
6
Press w e to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” ( ੬ below “Weekly/Daily Recording”)
● “REC MODE” ( ੬ pg. 29, 30, “Recording Mode”)
● “NAME” ( ੬ pg. 64, “Modify Title Name”) (DVD deck only)
7
Press ENTER to access the Program Confirmation screen.
8
Press ENTER to complete timer programing.
● To program another timer, repeat steps 3 – 8.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 35.
9
Press TIMER # to engage the unit’s timer mode. The DVD timer
lamp lights up on the unit and the unit is automatically turned off.
● To disengage the timer mode, press TIMER # again.
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
WEEKLY : Select to record a weekly program.
MON–FRI : Select to record a daily program from Monday through
Friday.
MON–SAT : Select to record a daily program from Monday through
Saturday.
SUN–SAT : Select to record a daily program from Sunday through
Saturday.
VCR Plus+ ® Timer Programing
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 5. When this
happens, set the correct Guide Channel number for that station.
(
੬ pg. 77, “Changing VCR Plus+ ® Setting”)
Cable Box and DBS Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using the VCR Plus+
system:
A Perform “VCR Plus+
® Timer Programing”.
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
rtwe
ENTER
CLEAR ( 8)
DVD
0 – 9
VHS
CANCEL
VCR Plus+ TIMER
RETURN
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “Changing VCR Plus+
® Setting” ( ੬ pg. 77) and
set the Guide Program number correctly.
1 2 3
4 5 6
7 8 9
0
SP
1 2 3 4
VCR Plus+ PRGM
DATE START STOP CH
DAILY/WEEKLY REC MODE
NAME
PLUSCODE NO.
ENTER VCR PLUS+ CODE WITH [0 - 9] KEYS
THEN PRESS [ENTER] OK
MV5S_00.book Page 31 Tuesday, March 8, 2005 7:38 PM