JVC SX-LC33MK2 - Manual (Page 2)

7
Attaching the feet
Attach the supplied feet on the bottom of the speaker, so that you
can protect the speaker cabinet, decrease the vibration of the
speaker cabinet and prevent the speaker from slipping.
• Place a large, thick cloth under the speaker in order to protect
the floor and the speaker.
When installing the speaker vertically
1 Stand the speaker upside down.
2 Attach the feet.
When installing the speaker horizontally
Install the speaker with the screw holes facing rightward.
1 Place the speaker with the side, where you attach the feet,
facing upward.
2 Attach the feet.
3 Attach the screw hole covers to the screw holes.
Screw holes on the side are designed for installing Speaker
Stand LS-M1 (purchased separately), when LS-M1 is not used,
use the screw hole covers to hide the holes.
Installing on LS-M1 (purchased separately)
Unpacking the feet supplied for LS-M1.
• Refer also to the manual supplied for LS-M1 for installation.
1 Peel off the feet, then attach them at the four corners of the
top plate of LS-M1.
2 Install this unit on LS-M1.
7
•
1
2
1
2
3
LS-M1
LS-M1
LS-M1 ( )
LS-M1
• LS-M1 LS-M1
1 LS-M1
2 LS-M1
SX-LC33MK2
Screw holes
7
•
7
—
•
• 6
Ω
• SX-LC33MK2 120 W
•
–
–
–
FM
–
–
•
•
7
1
2
—
OFC
OFC
OFC
ª ·
•
•
•
•
ª
ª
·
7
Connecting the speaker cord to the speaker
Connect the speaker cord to the speaker as follows.
1 Twist and remove the insulation at the end of each speaker cord
before connecting.
2 Rotate the speaker terminal knob counterclockwise and fit the
speaker cord into the groove. Then rotate the knob clockwise to
secure the cord.
About speaker cords—to improve the sound quality
About the OFC cord
The core wires of the supplied speaker cords are made of OFC
(Oxygen Free Copper). This OFC cord enables high quality sound
reproduction.
When connecting the speaker cords
Make sure to match the polarity (
ª and ·); otherwise, the surround
effect will become less effective.
After connecting, check that the exposed cores are fully inserted into
the terminal.
When using other speaker cords
Observe the following;
• Buy thick speaker cords rather than thin cords, and make them as
short as possible for connection.
• Do not use long speaker cords; otherwise, the sound quality may
deteriorate.
• Use speaker cords of the same length for both left and right
speakers.
• Using a special speaker cord such as a litz wire, a coaxial cable, or
a cord which has the specified connecting directionality may
influence the sound quality.
Tighten
Loosen
Silver
ª terminal
(Red)
· terminal
(Black)
Copper
To the speaker ª
terminal of amplifier
To the speaker
·
terminal of amplifier
English
Connection
7
Connecting the speaker system to the amplifier
Before connection—
• Turn off the power to the amplifier before connecting the
speaker system; otherwise, the speakers may be damaged.
• The impedance of the speaker is 6 Ω. Before connecting it to
your amplifier, check the speaker impedance range of your
amplifier. If the impedance of this speaker is out of the speaker
impedance range indicated on the amplifier, you cannot
connect this system to the amplifier.
• The maximum power handling capacity of the SX-LC33MK2 is
120 W. Excessive input will result in abnormal noise and
possible damage.
• Be sure to turn down the volume level to prevent unwanted
noise before performing following operations:
– Turning on or off other components,
– Operating the amplifier,
– Tuning FM stations,
– Fast-forwarding a tape,
– Continuously reproducing high frequency oscillation or high
pitch electronic sounds.
• When using a microphone, do not aim it at the speakers or use
it near the speakers; otherwise, the howling which occurs may
damage the speakers.
• Before replacing the cartridge, always turn off the power to the
turntable; otherwise, the clicking noise may damage the
speakers.
7
To remove the speaker grille
To remove the speaker grille, insert your fingers at the bottom of
the speaker grille, then pull upward.
To attach the speaker grille, put the projections of the speaker
into the holes of the speaker grille.
• Do not push the speaker grille strongly.
English English
·
Do not lean the speaker when installing;
otherwise, the speaker may fall over.
SX-LC33MK2
LS-M1
Bottom Peel off
Feet (black: supplied)
LS-M1
Peel off
Feet (black: supplied)
Top
Peel off
Feet
(black: supplied)
Peel off
Screw hole covers
(brown: supplied)