Learning commands, Controlling other components —continued, Press the button you want to learn the new command – Integra DHC-9.9 User Manual
Page 140: Remote indicator
140
The AV controller’s remote controller can learn the com-
mands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s
remote controller, the remote controller can learn it, and
then transmit the exact same command when its Play
[
] button is pressed in the CD remote mode.
This is useful when you’ve entered the appropriate
remote control code (page 137) but some buttons don’t
work as expected.
Notes:
• The following buttons cannot learn new commands:
Remote Mode, Macro [1], [2], [3], TV CH [+]/[–],
Re-EQ, Light.
• When you want to learn the command from your TV’s
Power button, select the TV remote control mode and
use the remote controller’s [Standby] button to learn
the command. In the TV remote control mode, the
remote controller’s [Standby] and TV [
] buttons
are linked, so using the [Standby] button to learn the
command will mean that you can also use the TV
[
] button to turn your TV on or off in TV remote
control mode.
• When you want to learn the commands from your
TV’s Channel Up and Down buttons, select the TV
remote control mode and use the remote controller’s
CH [+/–] button (left to the [Enter] button) to learn the
commands. In the TV remote control mode, the
remote controller’s CH [+/–] and TV CH [+]/[–] but-
tons are linked, so using the CH [+/–] button to learn
these commands will mean that you can also use the
TV CH [+]/[–] buttons to change channels in TV
remote control mode.
• The remote controller can learn approximately 70 to
90 commands, although this will be less if commands
that use a lot of memory are learned.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Integra/Onkyo CD players, cassette decks,
and DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands at any time by resetting the remote controller
(see page 138).
• To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
Learning Commands
1
While holding down the Remote
Mode button for the mode in
which you want to use the com-
mand, press the [On] button.
The Remote indicator lights up.
2
Press the button you want to
learn the new command.
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
+
-
On
Standby
TV
Input
TV CH
TV VOL
--/--- 10
11
12
D.TUN
+10
0
Clear
1
2
3
4
5
6
7
8
9
Input Selector
VCR
/
DVR
CBL
/
SAT
DVD
Tape
Tuner
CD
Phono
Game
/
TV
Macro
1
2
3
VCR
DVD
CDR/MD
CD
Zone
2
Remote Mode
Dimmer
Tape/AMP
Sleep
Receiver
TV
Dock
Cable
VOL
CH
Disc
Album
+
-
Enter
Top
Men
u
Men
u
Display
Muting
Exi
t
Gu
ide
Prev
CH
Ret
urn
Setu
p
SAT
Zone
3
AUX 1
AUX 2
1, 4
1
Remote
indicator
If the command is learned successfully,
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
Press any Remote Mode button when
you’ve finished.
POWER
SLEEP
DIMMER
SUR
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TUNER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUM
E
LEVEL
CH SEL
PRESET
MU
TING
TEST
TONE
MULTI-CH
INPUT
GROUP
R
10
--/-
--
11
12
R
em
ote M
ode
Zo
ne
2
DVD
VCR
CD
Zo
ne
3
Rec
eive
r
Cable
Dock
Tape
/A
M
P
SAT
CD
R/MD
+
-
T V
C
H
T V
V
O
L
Sleep
Input Selector
3
2
Macro
1
+10
0
Clear
D.TUN
1
2
3
4
5
6
7
8
9
Input
I
O
n
Sta
nd
by
T V
Ta
pe
D
V
D
DC
R/D
VR
CB
L/S
AT
AU
X1
AU
X2
Tu
ne
r
CD
Phono
Ga
ne
/TV
About 2 to 6
inches (5–15 cm)
Supplied
remote controller
(RC-691M)