Miller Electric Trailblazer DC User Manual
Page 3

TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Additional Symbols For Installation, Operation, And Maintenance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. California Proposition 65 Warnings
1-7. Principal Safety Standards
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles
2-2. Dangers relatifs au soudage à l’arc
2-3. Dangers existant en relation avec le moteur
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4. Dangers liés à l’air comprimé
2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
2-6. Principales normes de sécurité
2-7. Information sur les champs électromagnétiques
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Weld, Power, And Engine Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Dimensions, Weights, and Operating Angles
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Fuel Consumption While Welding
4-4. Fuel Consumption While Using Generator Power
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Stick And MIG Mode Volt-Ampere Curves
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. TIG Mode Volt-Ampere Curves
5-1. Installing Welding Generator
5-2. Engine Prestart Checks (Robin EH64-Powered Units)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Engine Prestart Checks (Kohler-Powered Units)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Activating The Dry Charge Battery (If Applicable)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Connecting To Weld Output Terminals
5-8. Selecting Weld Cable Sizes*
5-9. Remote Receptacle Information
5-10. Adjusting Wire (MIG) Weld Puddle Consistency
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATING WELDING GENERATOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Process/Contactor Switch On CC/CV Models
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Remote Amperage/Voltage Control
SECTION 7 − OPERATING AUXILIARY EQUIPMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Generator Power Receptacles And Circuit Breakers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Optional Generator Power Receptacles
7-3. Wiring Instructions For Optional 240 Volt, Single-Phase Plug (NEMA 14-50P)