Marantz SR6001 - Manual (Page 46)

ENGLISH
42
6-2 CHECK AUTO
These menus are for confirming the results of
AUTO SETUP function equalizer measurement
(AUDYSSEY, FRONT, FLAT).
1. Select “ 6. ACOUSTIC EQ ” from MAIN MENU
with the 3 or 4 cursor buttons and press the
ENTER button.
2. Select “ CHECK AUTO ” with the 3 or 4 cursor
buttons.
3. Press the ENTER button to enter the
selection.
C H E C K A U T O
M D :
A U D Y S S E Y 6 3 0 . 0
C H : F L 1 2 5 0 . 0
2 5 0 0 . 0
5 0 0 0 . 0
1 k 0 . 0
2 k 0 . 0
4 k 0 . 0
8 k 0 . 0
1 6 k 0 . 0
R E T U R N E X I T
63
125 500 2k 8k
250 1k 4k 16k
+9
0dB
-20
Select MD (mode) with the 3 / 4 cursor buttons
followed by the desired equalizer (“AUDYSSEY”,
“FRONT”, “FLAT”).
CH:
Select the channel to check with the 1 or 2 cursor
buttons.
Notes:
• The frequency will not be exactly the same as in the
Preset G. EQ modes.
• FL and FR are not indicated on the CHECK AUTO
2 menu.
4. Once fi nished checking, select “ RETURN ” with
the 3 / 4 cursor buttons and press the ENTER
button to return to the “6. ACOUSTIC EQ”
menu.
6-1 PRESET G. EQ ADJ
These modes allow you to set a 9-band graphic
equalizer for each of the 7 channels.
1. Select “ 6. ACOUSTIC EQ ” from MAIN MENU
with the 3 or 4 cursor buttons and press the
ENTER button.
2. Select “ PRESET G. EQ ADJ ” with the 3 or 4
cursor buttons.
3. Press the ENTER button to enter the
selection.
63
125 500 2k 8k
250 1k 4k 16k
P R E S E T A D J U S T
R E S E T :
C H 6 3 0 . 0
C H : F L 1 2 5 0 . 0
2 5 0 0 . 0
5 0 0 0 . 0
1 k 0 . 0
2 k 0 . 0
4 k 0 . 0
8 k 0 . 0
1 6 k 0 . 0
R E T U R N E X I T
+9
0dB
-20
RESET:
Using the 1 or 2 cursor buttons, select the
channel(s) to be reset to either the currently
displayed channel (“CH”) or all channels (“ALL”),
and press the
ENTER button to enter the setting.
“ALL” : Resets all channels.
“CH” : Resets only the currently displayed
channel.
CH:
Select the channel (“ FL ”, “ C ”, “ FR ”, “ SR ”, “ SBR ”,
“ SBL ” or “ SL ”) to adjust with the 1 or 2 cursor
buttons, and switch to the adjustment mode with
the
4 cursor button.
Frequency:
Select the target frequency on the graph with the
1 or 2 cursor buttons and press the ENTER button
to enter the selection. Adjust the level with the 3 or
4 cursor buttons. (Note that this can be adjusted
to any level between –20 and +9 dB in 0.5 dB
increments.)
Move to the next frequency with the
1 or 2 cursor
buttons, and adjust the level.
After you complete this portion of the setup, press the
ENTER button to enter the settings. Move cursor to
“ RETURN ” with the 3 , 4 , 1 and 2 cursor buttons and
press the ENTER button.