Marantz SR6001 - Manual (Page 40)

ENGLISH
36
3 SURROUND SETUP
This menu is for setting surround effect parameters
for the various surround input signals so as to bring
out the live audio effect of your speaker system.
• CHANNEL LEVEL:
“3-1 CHANNEL LEVEL” (see page 36)
• PLIIx MUSIC PARAMETER:
“3-2 PL II x MUSIC PARAMETER” (see page 37)
• CSII PARAMETER:
“3-3 CS II PARAMETER” (see page 37)
• NEO:6 PARAMETER:
“3-4 NEO:6 PARAMETER” (see page 37)
1. Select “ 3. SURR SETUP ” from the MAIN
MENU with the 3 or 4 cursor buttons and press
the ENTER button.
2. Select the desired menu with the 3 or 4 cursor
buttons and press the ENTER button.
3 . S U R R S E T U P
C H A N N E L L E V E L
P L x M U S I C P A R A M E T E R
C S P A R A M E T E R
N E O : 6 P A R A M E T E R
H T - E Q : O F F
L F E L E V E L :
R E T U R N N E X T E X I T
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
fi lm soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When Dolby Virtual Speaker is set for the
surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select “
0dB ”, “ –10 dB ” or “ OFF ” with 1 or 2 cursor
button.
After you complete this portion of the setup, move
the cursor to “
RETURN ” with the 3 , 4 , 1 , 2 cursor
buttons and press the ENTER button.
Note:
• After you complete this portion of the setup,
press the ENTER button to move the cursor to
“RETURN” and press the ENTER button again to
go to sub-menu.
3 . S U R R S E T U P
C H A N N E L L E V E L
P L x M U S I C P A R A M E T E R
C S P A R A M E T E R
N E O : 6 P A R A M E T E R
H T - E Q : O F F
L F E L E V E L :
R E T U R N N E X T E X I T
C H A N N E L L E V E L
S U R R . M O D E :
A U T O
C E N T E R : 0 . 0 d B
S U R R . R : 0 . 0 d B
S U R R . B R : 0 . 0 d B
S U R R . B L : 0 . 0 d B
S U R R . L : 0 . 0 d B
S U B W : 0 . 0 d B
R E T U R N E X I T
N E O : 6 P A R A M E T E R
C E N T E R G A I N : 0 . 3
R E T U R N N E X T E X I T
P L x M U S I C P A R A M E T E R
P A R A M E T E R : D E F A U L T
P A N O R A M A : O F F
D I M E N S I O N : 0
C E N T E R W I D T H : 3
R E T U R N N E X T E X I T
C S P A R A M E T E R
T R U B A S S : 0
S R S D I A L O G : 0
R E T U R N N E X T E X I T
☞
P. 37
☞
P. 36
☞
P. 37
☞
P. 37
3-1 CHANNEL LEVEL
1. Select “ 3. SURR SETUP ” from MAIN MENU
with 3 or 4 cursor buttons and press the
ENTER button.
2. Select “ CHANNEL LEVEL ” with the 3 or 4
cursor buttons and press the ENTER button.
3. Set the SURR. MODE with the 1 or 2 cursor
buttons.
C H A N N E L L E V E L
S U R R . M O D E :
A U T O
C E N T E R : 0 . 0 d B
S U R R . L : 0 . 0 d B
S U R R . R : 0 . 0 d B
S U R R . B A C K L : 0 . 0 d B
S U R R . B A C K R : 0 . 0 d B
S U B W : 0 . 0 d B
R E T U R N E X I T
4. Select the desired menu item with the 3 or 4
cursor buttons, set the desired level with the
1 or 2 cursor buttons, and press the ENTER
button.
SURROUND MODE:
The surround mode can be independently set for
3 modes.
1. Multi Ch STEREO
2. CS
II
3. Others
CHANNEL LEVEL
CENTER LEVEL:
Set the effect level of the center speaker between
–12 and +12 level in 0.5 level interval .
• If “NONE” was selected for the center speaker
setting in the SPEAKER SIZE, then this setting will
not appear.
SURR L or R LEVEL:
Set the effect level of the Surround speaker
between
–12 and +12 level in 0.5 level interval .
• If “NONE” was selected for the surround speakers
setting in the SPEAKER SIZE, then this setting will
not appear.
SURR. BACK L or R LEVEL:
Set the effect level of the Surround Back speaker
between
–12 and +12 level in 0.5 level interval .
• If “NONE” was selected for the surround back
speakers setting in the SPEAKER SIZE, then this
setting will not appear.