Marantz SR7200 - Manual (Page 26)

19
ENGLISH
J CONTROL indicator
Indicates when the < • 3 (CURSOR/TRANSPORT CONTROL
switching) ⁄1 is in a transport control mode such as PLAY, STOP, etc.
• If the LCD flickers when a button is pressed in order to transmit a
command or when in the LEARN mode, the transmission or learning
is not possible. In such a case, please replace the batteries.
• This remote controller uses non-volatile memory, so that learned
codes and macros will be preserved even if the batteries are
removed.
BASIC OPERATION
USE MODE
The remote controller will normally be used in the USE mode.
It comes preset with codes commonly used to control 11 types of
components manufactured by Marantz and Philips, including DSS,
DVD, TV, LD, VCR, AUX, TUNER, CD, TAPE, CD-R/MD, and AMP,
as well as many others that utilize the RC-5 remote control language.
1. Press once one of the Function buttons , to change to another
component’s commands, such as DVD button.
2. DVD will be displayed on the LCD and the function codes will be
set to operate the DVD player, and if you double clicked the DVD
function button, the preamplifier or receiver’s input will be
changed as well.
3. Now you can operate the DVD player. When a button is pressed,
the
symbol indicates that a remote code is being transmitted.
is not displayed if a button for which no code has been set is
pressed.
4. The Jog Dial n is used to select any one of up to 10 direct
operations that can be performed for each of the 11 functions (DVD,
TV, AMP, etc.). Rotate the Jog Dial n to select one of these
commands. The number of the current page is indicated by
- .
Page numbers cycle up or down, for example → → →
→ etc. or → → → → etc. depending on which way the
Jog Dial n is rotated.
The last page position for any given command function is retained
in the memory even if the remote controller is switched to the
command function for another component. (Last Memory)
If it is left for approximately 1 minute without pressing any buttons,
all items on the LCD will go off except the function indicator.
Even if the display goes off, the remote controller will hold the
page position and other data. The display may be activated again
by pressing any button.
LEARN MODE
The remote controller is capable of learning and memorizing the
remote control codes used by almost any other remote controller you
may already own.
• If no commands have been programmed for a particular function
button, the remote controller will transmit whatever codes have
been factory preset.
• The following example shows how to program your remote
controller and how to use the codes for a DVD player.
• The remote controller infrared receiver is located at the top of the
remote controller.
1. Use a ballpoint pen or other sharp point to press the MODE button
z until the LEARN indicator is displayed. Each time you press
this button, the mode will cycle through LEARN
→ NAME → USE.
Stop when the LEARN indicator starts to blink.
2. Place the DVD’s remote controller so that its infrared signal
transmitter is facing the infrared signal receiver on the Marantz
remote controller at a distance of about 5 centimeters (2 inches).
MEMO CLEAR GUIDE MUTE
C D DVD CD-R/MD
DSS T V VCR
AMP L D TUNER TAPE
AUX
AUTO DTS CS5.1 6.1
L D
DVD
ON
OFF
ON /OFF S OURCE
MA CR O MO DE
LEARNING REMO
T E
CONTR
OL RC 72
00 S R PO WER
ON
OFF
ON /OFF S O URCE MA CR O MO DE
LEARNING REMO
TE
CONTR
OL RC 72
00 S R PO WER
5 cm
Side View Side View
Top View Top View
DVD remote
control unit
DVD remote
control unit
DVD remote
control unit
DVD remote
control unit
RC7200SR
RC7200SR
RC7200SR
OK NO GOOD
RC7200SR