Basic operation, English, Listening to the tuner – Marantz SR7200 User Manual
Page 19
12
ENGLISH
BASIC OPERATION
LISTENING TO THE TUNER
MANUAL TUNING
1.
To select the tuner as the source, press the
TUNER
button
t
on
the front panel or press the
TUNER
button
,
on the remote
control unit.
2.
Press the
TUNER
button
t
on the front panel or press the
TUNER
button
,
on the remote control unit to select the desired
frequency band if required.
3.
Press the
F/P
button
!6
on the front panel to display the frequency.
4.
Press the
TUNING/PRESET
or button
!5
on the front panel or
press the
^
,
v
button
⁄0
on the remote control unit.
5.
If FM is selected, press the
MODE
button
!7
on the front panel or
select
T-MOD
by the
Jog Dial
n
and press the
ENT
button
m
in
the TUNER mode on the remote controller.
(FM) MODE BUTTON OPERATION
When “AUTO” indicator is on in the display, FM stations that broadcast
in stereo will be received in stereo and the “STEREO” indicator lights.
When “AUTO” indicator is off, all the FM stations will be received in
mono regardless of whether or not they are broadcasting in stereo.
AUTO TUNING
1.
Press the
F/P
button
!6
on the front panel to display the frequency.
2.
Press the
TUNING/PRESET
or button
!5
on the front panel
for more than 1 second to start the Auto tuning function.
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
Press
^
,
v
button
⁄0
for more than 1 second to start the Auto tuning
function.
PRESET TUNING
With this unit you can preset up to 30 FM/AM stations in any order. For
each station, you can memorize the frequency and reception mode if
desired.
1-a. Manual Presetting
1.
Refer to the “MANUAL TUNING” or “AUTO TUNING” section
above to tune in a desired station.
2.
Press the
MEMORY
button
!4
. “MEMORY” indicator starts blinking
on the display.
While “MEMORY” is still blinking (approx. 5 seconds), select the
preset number by pressing the
TUNING/PRESET
or button
!5
then press the
MEMORY
button
!4
again.
3.
When a number has been properly input, “MEMORY” indicator
stops blinking and goes out.
The station is now stored in the specified preset memory location.
1-b. Manual Presetting (Using the remote unit)
1.
Tune in a desired station.
2.
Press the
MEMO
button
⁄6
.
3.
Enter the desired preset number with ten keypad
⁄7
.
4.
Then, press
MEMO
button
⁄6
again to store.
2. Auto Presetting
This function automatically scans the FM and AM band and enters all
stations with sufficient signal strength into the memory.
1.
Press and hold down the
MEMORY
button
!4
and
TUNER
button
t
simultaneously for 3 seconds or more.
2.
“MEMORY“ will blink on the display.
3.
Each time the tuner finds a station, the scanning will pause and
memory. Auto presetting will starts.
4.
Operation stops automatically when all 30 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the
CLEAR
button
!3
.
3. Recalling a Preset Station
1.
Press the
F/P
button
!6
to change the display to preset.
2.
Select the desired preset station by pressing
TUNING/PRESET
or button
!5
on the front panel or press
CH
or
CH
button
⁄2
on the remote.
Note:
To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits using
the numeric keypad
⁄7
.
To return to the Manual Tuning mode, press the
F/P
button
!6
.
4. Preset Scan Tuning (Using the remote control unit)
1.
Select the
SCAN
by the
Jog Dial
n
and press the
ENT
button
m
in the TUNER mode on the remote controller. (The preset station
with the smallest preset number is recalled first. If no stations have
been preset, “NO PRESET” shows in the display and the unit
returns to the previous mode.)
2.
Preset stations are recalled in sequence (CH-1
→
CH-2, etc.) for 5
seconds each. Preset numbers that do not contain stations are
skipped.
3.
You can fast forward the preset stations by pressing the
CH
button continuously.
When the desired preset station is received, cancel the preset scan
operation by pressing the
CH
button or the
CLEAR
button
⁄5
.
5. Clearing Preset Stations
You can remove preset stations from memory using the following
procedure.
1.
Recall the preset number to be cleared with the method described
in “Recalling” a preset station.
2.
Press the
CLEAR
button
!3
on the front panel or
CLEAR
button
⁄5
on the remote control unit for 3 seconds or more.
“CLEAR” appears on the display to indicate that the specified
preset number has been cleared.
6. Frequency Direct Call
1.
Select
F-DIR
by the
Jog Dial
n
and press the
ENT
button
m
in
the TUNER mode on the remote controller.
2.
Display shows “FM– – –.– –MHz” (at FM mode).
3.
Input your desired frequency with tenkeypad buttons on the
remote controller.
Eg) 98.1 MHz
Press
9
,
8
,
1
and
0
4.
Press the
ENT
button
m
again.