Marantz PMD570 - Manual (Page 22)

BALANCED IN R L
R E F = + 1 6 d B u / 0 d B F S
+ 24 + 24
GROUND
HOT (+) COLD (-)
2 1 3 L
R
IN OUT
ANALOG DIGITAL
IN
OUT
(SPDIF)
I / O RS 232C REMOTE2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
C A U T I O N
UL
C US LISTED
AUDIO SYSTEM 69 FM
S E R I A L N O .
WARNING: SHOCK HAZARD- DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
A C I N
MODEL NO. PMD570
AC120V 60HZ 0.5A
MADE IN JAPAN
REMOTE1
Back continued
2 3 4 5
- 22 -
3. DIGITAL IN & OUT
connectors (SPDIF)
Digital audio cable with RCA
jacks can be used for input and
output.
DIGITAL IN jack (RCA)
Connect a digital audio cable with an RCA jack from
an external device providing SPDIF digital output*.
To record from this input Dig-In must be selected
from the input menu.
*Incoming source must be at 44.1 or 48 kHz.
DIGITAL
IN
OUT
(SPDIF)
Example
display at
stop.
is flashing.
6. Turn the Jog Wheel so Dig-In is flashing.
7. Push and release the Jog Wheel to accept the Dig-
In choice.
8. Push and release the MENU/STORE button to
store the Menu change. Stored is displayed.
See page 24 for a full presentation of Menu
selection.
DIGITAL OUT jack (RCA)
Connect a digital audio cable with RCA jacks to an
external device accepting a SPDIF digital input. This
connection will pass a digital signal when the
PMD570 is recording, in record pause or during
playback.
4. I/O port
Plug an I/O cable in here and
connect the other end to your
computer (PC or MAC).
To activate I/O:
From power off, push and hold the MENU/STORE
button while you power on by pushing and releasing
the POWER ON/OFF button.
The connection makes it easy to copy audio files to
your computer's hard drive. The I/O connection can
only be made active when the PMD570 is off (neither
recording or during playback).
See page 43 for a full discussion of the I/O connection.
I / O
2. ANALOG IN / OUT jacks continued
choice is flashing.
6. Turn the Jog Wheel so UnBal. is flashing.
7. Push and release the Jog Wheel to accept the
UnBal. choice.
8. Push and release the MENU/STORE button to
store the Menu change. Stored is displayed.
See page 24 for a full presentation of Menu
selection.
L & R ANALOG OUT jacks
Plug L and R RCA jacks in here to
connect to the Line level input jacks
of an external pre-amplifier, mixer
or recording device.
This connection will pass a line
level signal during recording, record
pause and playback.
L
R
IN OUT
ANALOG
TIME
REC REMAIN L
R
-dB over 0 2 6 12 20 40 00
-dB
To select the DIGITAL IN jack as input for recording:
1. Push and release the MENU/STORE button.
2. Choose a Preset by turning the Jog Wheel.
3. Select the Preset by pushing and releasing the Jog
Wheel.
4. Turn the Jog Wheel so Input is flashing.
5. Push and release the Jog Wheel so the input choice
5. REMOTE 2
The REMOTE2 jack accepts the
optional wired remote Marantz
model RC600. Model RC600 has
a record indicator light.
REMOTE2
Model RC600 permits:
• starting recording
• pausing recording, and
• adding EDL marks
Model RC600 connects via a TRRS (Tip Ring Ring
Sleeve) connector.