Marantz SR4600 User Manual
Page 31
ENGLISH
28
7.1 CH INPUT
The SR4600 is equipped for future expansion
through the use of Multi channel SACD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected
to the L(front left), R (front right), CENTER, SL
(surround left), SR (surround right) and SBL
(surround back left) and SBR (surround back right)
channels of the 7.1 CH. IN jacks are output directly
to the front (left and right), center, surround (left
and right) and surround back speaker systems as
well as the pre-out jacks without passing through
the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer)
jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the
Monitor Outputs
.
This permits simultaneous viewing with video
sources
1.
Select a desired Video source to decide the
routed video signal to the
Monitor Outputs .
2.
Press the
7.1 CH INPUT
button on the front
panel or press
7.1 CH IN
on the remote to
switch the 7.1 channel input.
Recording the video from one source and the
audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from a
compact disc player connected to CD IN and the
video from a video camera connected to VCR1 to
video cassette recorder connected to the DSS/
VCR2 OUT jack.
1.
Switch the video output source to VCR1 by
simply pressing the
input selector
buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the
input selector
buttons on the
remote.
3.
Now “CD” has been selected as the audio input
source and “VCR1” as the video input source.
Notes:
• If you change the input source during recording,
you will record the signals from the newly selected
input source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog .
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
HT-EQ
Press the
HT-EQ
button on the front panel to turn on
the HT-EQ mode.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back over
audio equipment in the home. This is because film
soundtracks were designed to be played back in
large movie theater environments.
Activating the HT-EQ feature when watching a film
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
SURROUND
AV SURROUND RECEIVER SR4600
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT
PURE
DIRECT
AUTO
HT-EQ
MODE
DISP
MULTI
SLEEP
AUTO
POWER ON/STANDBY
S. SPEAKER B
1.
2.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
VCR1
DSS/VCR2
TV
AUX1
1.
2.
CHANNEL/SKIP
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII
EX/ES
VIRTUAL
DTS
PURE DIRECT
AUTO
3
2
1
6
5
4
9
8
0
7
T.TONE
MENU OFF
SET UP/
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
ENTER
AUX1
2.
4.
1.
SURROUND
AV SURROUND RECEIVER SR4600
DOWN
INPUT SELECTOR
PHONES
STANDBY
MUTE
7.1CH INPUT
PURE
SETUP
DIRECT
SIMPLE
AUTO
HT-EQ
MENU
ENTER
DISPLAY
MEMORY
CLEAR
T-MODE
EXIT
BAND
MODE
DISP
MULTI
AUTO
TUNED
ST
V – OFF
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.1
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL
S
SR
LFE
POWER ON/STANDBY
S. SPEAKER B
DOWN
UP
VOLUME
MUTE
ATT
MEMORY
CLEAR
T-MODE
BAND
DIGITAL
SURROUND
L
C
R
SL
S
SR
LFE
4.
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR4600 is sent to
the record outputs.
This means that any program you are watching or
listening to may be recorded simply by placing
machines connected to the outputs for
TAPE OUT,
CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT
in the record mode.
To record the input source signal you are currently
watching or listening to
1.
Select the input source to record by turning
the
INPUT FUNCTION SELECTOR
knob on
the front panel or simply press the
input
selector
buttons on the remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the
TAPE OUT, CD-R/MD OUT,
VCR1 OUT, and DSS/VCR2 OUT
outputs for
recording.
3.
Start recording to the recording component as
desired.
SURROUND
AV SURROUND RECEIVER SR4600
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT
PURE
SETUP
DIRECT
SIMPLE
AUTO
HT-EQ
MENU
ENTE
MODE
DISP
MULTI
AUTO
TUNED
ST
V – OFF
NI
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.
POWER ON/STANDBY
S. SPEAKER B
1.
MENU
OSD
VOL.
TV
VOL.
MAIN
SLEEP
MUTE
AMP
TUNER
CD
TAPE
CDR/MD
DVD
POWER
VCR1
DSS/VCR2
TV
AUX1
1.
MAIN
05.5.20, 5:41 PM
Page 28