Marantz SR4600 - Manual (Page 15)

ENGLISH
12
Caution:
• Be sure to use speakers with the specified impedance
as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
speaker wires touch
each other and do
not let them touch
any metal part of
this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause you
to receive an electric shocks.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
• Be sure to connect the positive and negative
cables for the speaker properly. If they are miss-
connected, the signal phase will be reversed and
the signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in ).
If your subwoofer is a passive type (power amplifier
is not built in), connect a monaural power amplifier
to the PRE OUT SUBWOOFER jack and connect
the subwoofer to the amplifier.
CONNECTING AUDIO COMPONENTS
IN OUT MONITOR VCR1
MONITOR
R SR
C
SW SBR
SL SBL L
R
SPEAKER SYSTEMS MINIMUM 6 OHMS
CENTER
R
FRONT SURROUND BACK SURROUND
L L L R
DVD OUT IN MONITOR TV DVD VCR1 OUT IN DSS / VCR2 OUT
VIDEO
IN Y
DSS / VCR 2 DVD COAX. OUT 4 3 OPT.
OUT 2 1 7.1CH INPUT
L SL C SBL
SBR SW SR R TV DVD VCR1 OUT IN IN OUT DSS / VCR2 IN OUT CDR/MD TAPE
PRE OUT
OUT IN CD
R
L
FM (75 Ω ) GND AM
CB/PB
CR/PR
AUDIO
ANTENNA
RC-5
DIGITAL
COMPONENT VIDEO
AUDIO AC IN
S-
VIDEO
S. SPEAKER B AC OUTLETS 120V 60HZ
1A 120W MAX
UNSWITCHED
SWITCHED
1A 120W MAX
TAPE OUT IN CD
R
L
IN CDR/MD 4 OPT.
OUT 1
DIGITAL
OUT
OUT IN
L
R
L
R
OUT
L
R
L R L R L R
R L R L R L
OUT IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R L
R L R L
R L
L
R
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the same signal
which is currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and 2
optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other
digital source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These jacks
can be connected to a CD recorder-, or a MD
deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2 input
jacks. Use 75 ohms coaxial cables (for digital
audio or video) for DIG-3, 4 input jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 17.
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard. If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
05.5.20, 5:40 PM Page 12