Multi-Tech Systems MT2456SMI22 - Manual (Page 57)

Index
Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide 57
Index
$F – FastConnect Control , 33
%L - Report Line Signal Level , 24
%Q - Report Line Signal Quality , 24
&C - RLSD Option , 17
&D - DTR Option , 17
&F - Restore Factory Configuration (Profile) , 14
&G - Select Guard Tone , 23
&K - Flow Control , 17
&P - Select Pulse Dial Make/Break Ratio , 23
&R - RTS/CTS Option , 18
&T - Local Analog Loopback Test , 14
&V - Display Current Configuration and Stored Profiles ,
23
** - Load to Internal RA , 14
*B - Display Blacklisted Numbers , 24, 25
+ESA - Configure Synchronous Access Submode , 31
+ESR - Selective Repeat , 29
+GCI - Country of Installation , 13
+IBC – In Band Commands , 19
+IFC - DTE-Modem Local Flow Control , 18
+MS - Modulation Selection , 27
+PCW - Call Waiting Enable , 26
+VCID - Caller ID (CID) , 12
+VDR - Distinctive Ring , 26
+VRID - Report Retrieved Caller ID (CID) , 12
A - Answer , 22
B - ITU-T or Bell , 28
B - Transmit Break to Remote , 29
Country Certifications, 48
D - Dial
, 21
Design considerations
Vendor recommendations , 49
E - Command Echo , 15
Electrical Characteristics , 9
EMC, Safety, and R&TTE Directive Compliance , 56
FCC Regulations , 52
G - Modem-to-Modem Flow Control (XON/XOFF) , 18
H - Disconnect (Hang-Up) , 22
Handling Precautions , 9
I - Identification , 13
International Modem Restrictions , 56
K - Break Control , 30
L - Speaker Volume , 22
Mechanical Specifications , 6
Multi-Tech Systems, Inc. Compliance , 52
N - Operating Mode , 12
New Zealand Telecom Warning Notice , 55
O - Return to On-Line Data Mode , 22
P - Set Pulse Dial Default , 22
Physical Dimensions , 6
Pin Configurations , 7
Placement, SocketModem , 51
Product Approvals , 48
Safety considerations , 50
Serial Demo Board block diagram , 47
South African Statement, Regulations , 56
Specifications,Mechanical , 6
Specifications,Technical , 5
–STE= - Set Telephony Extension , 25
T - Set Tone Dial Default , 22
Table of Result Codes , 16
Technical Specifications , 5
-TRV – Tip and Ring Voltage Measurement , 34
-TTE - Threshold Adjustments for Telephony Extension ,
34
V.22bis Commands
$F – FastConnect Control , 33
%L - Report Line Signal Level , 24
%Q - Report Line Signal Quality , 24
&C - RLSD Option , 17
&D - DTR Option , 17
&F - Restore Factory Configuration (Profile) , 14
&G - Select Guard Tone , 23
&K - Flow Control , 17
&P - Select Pulse Dial Make/Break Ratio , 23
&R - RTS/CTS Option , 18
&T - Local Analog Loopback Test , 14
&V - Display Current Configuration and Stored Profiles ,
23
** - Load to Internal RA , 14
*B - Display Blacklisted Numbers , 24, 25
+ESA - Configure Synchronous Access Submode , 31
+ESR - Selective Repeat , 29
+ETBM - Call Termination Buffer Management , 29
+GCI - Country of Installation , 13
+IBC – In Band Commands , 19
+IFC - DTE-Modem Local Flow Control , 18
+MS - Modulation Selection , 27
+PCW - Call Waiting Enable , 26
+VCID - Caller ID (CID) , 12
+VDR - Distinctive Ring , 26
+VRID - Report Retrieved Caller ID (CID) , 12
A - Answer , 22
B - ITU-T or Bell , 28
\B - Transmit Break to Remote , 29
Call Control Commands , 21
D - Dial , 21
E - Command Echo , 15
FastConnect Command , 33
\G - Modem-to-Modem Flow Control (XON/XOFF) , 18
Generic Modem Control , 12
H - Disconnect (Hang-Up) , 22
I - Identification , 13
\K - Break Control , 30
L - Speaker Volume , 22
Line Side Device Commands , 34
M - Speaker Control , 23
Modulation Control Commands , 27
\N - Operating Mode , 12
O - Return to On-Line Data Mode , 22
P - Set Pulse Dial Default , 22
Q - Quiet Results Codes Control , 15