MITSUBISHI ELECTRIC WD-52527 - Manual (Page 28)

28
Chapter 2. Connecting
A/V Receiver (Stereo System)
Figure 7
A coaxial digital audio cable or stereo audio cables are required.
These cables are not provided with the TV.
• To connect an analog A/V receiver:
Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
• To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of a digital audio cable to DIGITAL
AUDIO on the back of the TV. Connect the other end
to the COAXIAL DIGITAL INPUT on the back of the
A/V receiver.
*/ */ */ */ */ */ */ */ 065 065 065 065
"69 $% 5"1& 5"1& 7$3 7$3 57 %7%
.0/*5037$37$357%7%
.0/*5037$37$357%7%
065
065
*/
*/
*/
*/
*/
*/
*/
*/
065 065
065 065
$&/5&3
46#
800'&3
'30/5 463
3&$ 4063$&
-*/&065 13&065 463306/% 41&",&34
'30/5 41&",&34" '30/5 41&",&34# $&/5&3
7 .*/
-
-
- -
3
-
3
3
3
5)*4%&7*$&$0.1-*&48*5)1"350'5)&
'$$36-&401&3"5*0/*446#+&$5505)&
'0--08*/(580$0/%*5*0/4 5)*4%&7*$&
.":/05$"64&)"3.'6-*/5&3'&3&/$&"/%
5)*4%&7*$&.645"$$&15"/:*/5&3'&3&/$&
3&$&*7&%
*/$-6%*/(*/5&3'&3&/$&5)"5.":
$"64&6/%&4*3&%01&3"5*0/
."/6'"$563&%6/%&3-*$&/4&'30.%0-#:-"#03"503*&4-*$&/4*/(
$03103"5*0/%0-#:
130-0(*$"/%5)&%06#-&%4:.#0-"3&
53"%&."3,40'%0-#:-"#03"503*&4$03103"5*0/
$01:3*()5%0-#:-"#03"503*&4
*/$"--3*()54
3&4&37&%
*/165 015*$"-
*/165 $0"9*"-
*/165 $0"9*"-
%*(*5"-"6%*0
48*5$)&% 6/48*5$)&%
"$7)[ 505"-8
"."9 "$065-&54
.*546#*4)* "6%*07*%&03&$&*7&3
.0%&- .73
108&34611-:
108&3$0/46.15*0/ 7)[
8
7"
%*453*#65&%#: .*546#*4)*$0/46.&3&-&$530/*$4".&3*$" */$ "5-"/5*$#-7%."%&*/ +"1"/ /03$3044
("'"#3*26&&/
+"1"/
"7*4
3*426&%&$)0$&-&$530/26& /&1"4&/-&7&3 3*4,0'&-&$53*$4)0$, %0/0501&/
"/5&//"
7
7
'.
".
(/%
"560 45"/%#:
0/ 0'' S
T
47*%&0
7*%&0
"6%*0
8"3/*/(
"73FDFJWFS3FBS1BOFM
57CBDLQBOFM
*/
57
-
3
*/165 $0"9*"-
3FE
8IJUF
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
OUTPUT
AUDIO OUTPUT RECORD OUTPUT DVI Analog Audio
1 2 VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
SERVICE PORT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1
2
IEEE 1394 INPUT/ OUTPUT
Net Command IR EMITTER ¸
'
,INK ¸
INPUT
3
DTV/CABLE/ VHF/UHF
USE WITH CableCARD TM ANT 1 / MAIN ANT 2 / AUX
3FE
8IJUF
6TFJG
DPOOFDUJOH
BOBOBMPH
"7SFDFJWFS 6TFJG
DPOOFDUJOHB
%PMCZEJHJUBM
"7SFDFJWFS
Figure 7. Connecting an A/V receiver
Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on the
TV back panel.
2. Connect a set of audio cables from AUDIO OUT on the
satellite receiver back panel to INPUT-2 AUDIO, on the
TV back panel. The red cable connects to the R (right)
channel and the white cable connects to the L (left)
channel.
Note: Refer to the Satellite Receiver Owner’s Guide
for Dish Antenna connections.
57CBDLQBOFMTFDUJPO
:$ -
3
-
3
7*%&0065 "6%*0065 "6%*0*/
8IJUF
3FE
3FE
8IJUF
BOZ4WJEFPEFWJDF
INPUT
1 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
Note: NetCommand® will assume you
connected your Satellite Receiver to Input-2. If
you add a second Satellite Receiver or use any
other inputs for your Satellite Receiver, this
change must match in the NetCommand system.
See Editing NetCommand Setup in Chapter 3 for
more information.
Figure 8. Connecting a Satellite Receiver with S-Video
Note: On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the TV
as a digital signal. This is not anticipated to be a
common situation. To hear these copy-protected
signals through the A/V receiver, use connections
for analog A/V receivers.