MITSUBISHI ELECTRIC WD-52527 - Manual (Page 22)

22
Chapter 2. Connecting
Connecting External Devices and NetCommand ® Setup
Model
M-VR800 &
M-VR1000
Model
M-VR900 &
M-VR700
Model
Lifestyle ®28
Model
AVR-2700
Model
DTR-9.1
Model
VR-2080
Model
SR8200
Model
VSX-D557
Model
VSX-9TX
Model
RSX-1065
Model
STR-DE825
Model
RV-X2095
Model
RX-V2200
Device Audio Output to AV Receiver Inputs by Name
VCR VCR 1 VCR VCR VCR-1 Video 1 Video 1 VCR1 VCR/Tape VCR 1/DVR Video 2 Video 1 VCR 1 VCR 1
Satellite Receiver Aux Cable/DBS AUX CD Video 3 Video 3 DSS CD SAT Video 4 TV/DBS TV/DBS D-TV/LD
DVD Player DVD DVD (built-in) DVDVDP DVD Video 4 DVD LD/SAT DVD/LD Video 5 TAPE/MD CD DVD
TV Monitor Output
(& Digital Audio) TV TV TV TV/DBS Video 4 Video 4 TV DVD/TV TV Video 1 DVD/LD DVD/LD CBL/SAT
Chart 2
Mitsubishi 1 Mitsubishi 2 Bose Denon Integra Kenwood Marantz Pioneer 1 Pioneer 2 Rotel Sony Yamaha 1 Yamaha 2
TV
FJUIFSBOBMPHTUFSFPPS
EJHJUBMDPBYJBMBVEJPDBCMFT
"7
SFDFJWFS
*3&NJUUFST
WJEFPBOETUFSFP
BVEJPDBCMFT
EFWJDFUPCF
DPOOFDUFE
TUFSFPBOEPS
EJHJUBMBVEJPDBCMFT
NetCommand is able to control many current audio and video devices by sending remote control signals from the TV
to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio
video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or
learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the
TV and A/V receiver back panels match the NetCommand setup that is displayed on-screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this
chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below.
The following charts show which preset inputs you should use on the TV and A/V receiver.
Chart 1 shows TV inputs.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand. Only audio
should be connected to the A/V receiver.
Chart 1
Default Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service ANT-1
Antenna/Cable (digital/analog) ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
Cable box Component-1
VCR Input-1
Satellite Receiver Input-2
Camcorder Input-3 (on front panel)
DVD Player Component-2
After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for
connecting each device, custom name devices, add devices not included in the presets above or delete devices no
longer used. See Edit NetCommand. See Helpful Hints, at the end of this chapter for additional information on device
setup.