Philips MZ7-37 - Manual (Page 24)

24
English
CLOCK TIMER
Viewing the Clock
You can view the clock (if it is set) while
the system is in standby mode or any
source mode. It will be displayed for about
seven seconds.
• Press CLOCK/TIMER briefly (on the
system only).
™ “PM 10:38” (the current time)
will be displayed.
™ “--:--” will be displayed if the
clock is not set.
Setting the Clock
The clock is set in 12-hour mode, e.g. “ AM
12:00“ or “PM12:00“. Before setting
the clock, you must be in the View Clock
mode.
1 Press CLOCK/TIMER to select clock
mode.
™ “PM 12:00” or the current time
starts flashing.
2 Press S or T to set the hour
(PRESET mode OFF).
3 Press S or T to set the
minute (PRESET mode ON).
4 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
STOP on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode automatically.
– When a power interruption occurs, the
clock setting is erased.
BACK
REC/CD SYN PROG/A. REV
FLAT PRESET STOP
LOUDNESS
INCREDIBLE
SURROUND
TREBLE BASS DOLBY B NR
CLOCK/
TIMER 3 CDC
TAPE
CDR/AUX
TUNER
DIGITAL STEREO HIFI SYSTEM
DUBBING
NORMAL•FAST
60Hz 250Hz 500Hz 1KHz 2KHz 4KHz 8KHz SOUND VOLUME
PRESET AM LW TRACK REPEAT MW FM STEREO PROGRAM TIMER SHUFFLE
SURROUND INCREDIBLE
FLAT
LOUDNESS
CD CHANGER
T.A.
NEWS
SLEEP
DIM
REC
FRONT
HSD
DIM PLAY
DIGITAL CONTROL
SEARCH/TUNE
PRESET ▲ ▲
/
A•B
Setting the Timer
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will start to
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than 2 seconds to select timer mode.
™ “AM 12:00” or the last set timer
starts flashing. The TIMER flag
flashes.
™ The last selected source is lit while
other available sources are flashing.
2 Press 3 CDC, TUNER or TAPE to select
the desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press S or T to set the hour
for the timer to start (PRESET mode OFF).
4 Press S or T to set the
minute for the timer to start (PRESET
mode ON).
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The
TIMER flag remains on the display.
• To exit without storing the setting, press
STOP.
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the last
selected disc. If the CD trays are empty,
the TUNER will be selected instead.
– If the source selected is TAPE, and if the
preset time is reached during high
speed dubbing, the TUNER will be
selected instead.
– If the recording is active, the timer will
be cancelled.