Philips MZ7-37 - Manual (Page 23)

23
English
RECORDING
Notes:
– For recording, use only tape of IEC type I
(normal tape) or IEC type II (Cr02).
– The tape is secured at both ends with
leader tape. At the beginning and end of
tape, nothing will be recorded for six to
seven seconds.
– The recording level is set automatically,
regardless of the position of Volume,
Incredible Surround or Bass/Treble.
– To prevent accidental recording, break
out the tab on the left shoulder of the
tape side you want to protect.
– If “CHECK TAPE” is displayed, the
protection tab has been broken. Put a
piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape
detection hole when covering the tab
opening.
One Touch Recording
• For One Touch Recording, as soon as you
press REC, the current source (3 CDC,
TUNER or CDR/AUX) will be recorded on
tape deck 2
1 Load a blank tape in tape deck 2.
2 Press REC to start recording.
™ The REC flag starts flashing.
3 Press STOP to stop recording.
Note:
– When you press RECORD while in TAPE
mode, "SELECT SOURCE" will be
displayed. One Touch Recording is not
possible in TAPE mode.
Recording from other sources
(only on tape deck 2)
1 Press TAPE to select tape deck 2.
2 Load a blank tape into tape deck 2 with
the open side downward.
3 Press SIDE on remote control to select
the recording side.
™ The
BACK or FRONT flag will be
displayed, depending on the side
selected.
4 Press 3 CDC, TUNER or CDR/AUX.
• Start playback of the selected source.
5 Press REC to start recording.
™ The REC flag starts flashing.
6 Press STOP to stop recording.
Notes:
– Only
е е е е е or з з з з з mode is available
during recording.
– During recording, it is not possible to
listen to another source.
Dubbing tapes (from tape deck 1 to
tape deck 2)
1 Press TAPE to select tape deck 2.
2 Load the prerecorded tape into tape
deck 1 and a blank tape into tape deck
2.
• Make sure the tape in tape deck 1 has
its full spool to the left.
3 (For Tape Deck 2 only)
Press SIDE on the remote control to
select the recording side.
4 Press DUBBING NORMAL•FAST
once for normal speed dubbing or
twice (within 2 seconds) for high speed
dubbing.
™ “NORMAL” (normal speed) or
“ FAST” (high speed) will be
displayed, followed by
“
DUBBING”.
™ The HSD flag appears on the display
during high speed dubbing.
• Dubbing will start immediately.
™ The REC flag starts flashing.
5 Press STOP to stop dubbing.
Notes:
– Only
е е е е е mode is available during
dubbing.
– At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 1 to tape deck 2.
– To ensure good dubbing, use tapes of
the same length.
– During high speed dubbing in Tape
mode, the sound is reduced to a low
volume.
– You can listen to another source while
dubbing.
CD Synchro Start Recording
During CD synchro start recording,
• Do not fast forward/rewind your tape in
tape deck 1.
• Do not listen to another source.
1 Press TAPE to select tape deck 2.
• Load a blank tape into tape deck 2 with
the open side downward.
2 Press SIDE on remote control to select
the recording side.
3 Press A. REV to select the playback
mode ( е е е е е or з з з з з ).
4 Press 3 CDC.
• You can program the tracks in the order
you want them to be recorded (see
Programming Tracks). If you do not, the
tracks are recorded according to the
order on the selected disc.
5 Press CD SYN to start recording.
™ The REC flag starts flashing.
6 Press STOP to stop recording CD
playback.
Digital Recording via Digital
Out
For CD digital recording, please refer to the
Instructions Manual of the CD Recorder,
digital audio equipment, etc.