Motion Computing 002-15-0010 - Manual (Page 2)

Motion MCW with MediaWave Computer – Installation and Assembly Procedure
ii Document No. 002-15-0010
Motion Proprietary & Confidential
Copyright © 2009 Motion Computing, Inc. as an unpublished work
Table of Contents
REVISION HISTORY ................................................................................................................................................ I
TABLE OF CONTENTS ...........................................................................................................................................II
1. BASE WITH POWER SUPPLY SHROUD INSTALLED ............................................................................. 1
1.1 R EMOVE THE PLASTIC S HROUD THAT COVERS THE POWER SUPPLY .................................................................. 1
2. COLUMN ASSEMBLY ..................................................................................................................................... 1
2.1 L AY BASE ON ITS BACK .................................................................................................................................... 2
2.2 P OSITION COLUMN ABOVE BASE ....................................................................................................................... 2
2.3 I NSERT BOLTS THROUGH THE BOTTOM OF THE CART INTO THE COLUMN . T HREAD EACH BOLT BEFORE FULLY
TIGHTENING ANY BOLT . T IGHTEN ALL FOUR BOLTS . ........................................................................................ 3
2.4 S ET CART UPRIGHT ........................................................................................................................................... 3
2.5 R EMOVE ONE SCREW AND LOOSEN THE OTHER SCREW OF THE COLUMN TOP PLATE ......................................... 4
2.6 I NSERT DECORATIVE COVER IN THE BACK OF THE COLUMN CHANNEL GROVES . ............................................... 4
2.7 S LIDE DECORATIVE COVER DOWN TO WITHIN 24 INCHES OF THE BASE ............................................................. 4
2.8 R OUTE CABLES BEHIND THE DECORATIVE COVER ............................................................................................ 5
2.9 S LIDE DECORATIVE COVER TO THE BOTTOM OF THE COLUMN .......................................................................... 5
2.10 H OLDING CABLE IN THE CHANNEL AND INSERT SECOND DECORATIVE COVER IN THE BACK COLUMN CHANNEL
GROVES ............................................................................................................................................................ 5
2.11 S LIDE THE DECORATIVE COVER DOWN SO IT TOUCHES THE FIRST COVER ......................................................... 6
3. INSTALLING THE WORK SURFACE AND DRAWER ............................................................................. 6
3.1 R EMOVE THE DRAWERS BY PRESSING THE PLASTIC RELEASE TABS ON THE INSIDE OF THE DRAWER GLIDE
RAILS ................................................................................................................................................................ 6
3.2 N OTE WHERE THE A LLEN SET SCREWS ARE LOCATED ...................................................................................... 7
3.3 S LIDE THE WORK SURFACE DRAWER ASSEMBLY MOUNTING BRACKET INTO THE ADJUSTABLE RAIL LOCATED
ON THE FRONT COLUMN ................................................................................................................................... 7
3.4 S LIDE THE WORK SURFACE DRAWER ASSEMBLY DOWN THE RAIL TO ABOUT 2 INCHES (4.4 CM ) FROM THE
BOTTOM OF THE RAIL . ...................................................................................................................................... 7
3.5 T IGHTEN THE SET SCREWS ................................................................................................................................ 8
3.6 F ULLY TIGHTEN THE SET SCREWS ..................................................................................................................... 8
3.7 R EINSTALL THE DRAWER BY SLIDING IT ONTO THE DRAWER RAILS .................................................................. 9
4. ASSEMBLE THE CPU/MONITOR VESA MOUNT ASSEMBLY ............................................................ 10
4.1 A TTACH METAL SPACERS TO THE FRONT CPU VESA M OUNT PLATE CORNERS ............................................. 10
4.2 P LACE NYLON SPACERS OVER THE M ONITOR VESA M OUNT PLATE THREADED INSERTS WHERE ARROWS
INDICATE ........................................................................................................................................................ 10
4.3 I NSERT SCREWS THROUGH THE FRONT CPU VESA M OUNT PLATE HOLE AND THROUGH THE NYLON SPACERS ,
THREADING THEM INTO THE M ONITOR VESA M OUNT PLATE THREADED INSERTS ........................................ 11
4.4 A TTACH THE F LUSH T ILTING VESA M OUNT BRACKET TO THE BACK CPU VESA M OUNT PLATE ................ 11
4.5 P LACE THE M EDIA W AVE C OMPUTER ONTO THE FRONT CPU VESA M OUNT PLATE , EVENLY SPACED
BETWEEN THE METAL SPACERS AND CONNECTORS FACING DOWN ................................................................. 11
4.6 A TTACH THE BACK CPU VESA M OUNT PLATE TO THE FRONT CPU VESA M OUNT PLATE , USING THE
THREADED METAL SPACERS ATTACHED TO THE FRONT PLATE ........................................................................ 12
5. INSTALL THE MONITOR/CPU MOUNT ASSEMBLY BY SLIDING THE FLUSH TILTING VESA
MOUNT BRACKET INTO THE FRONT OF THE COLUMN RAIL ...................................................... 12
5.1 P OSITION THE VESA M OUNT BRACKET ABOUT ONE INCH FROM THE TOP OF THE COLUMN RAIL AND SECURE
BY TIGHTENING THE SET SCREWS ................................................................................................................... 13
6. ASSEMBLE THE BATTERY GAUGE HOUSING ..................................................................................... 13