FUJITSU Network Scanner fi-6010N - Manual (Page 13)

15
Chapter 6 Performing a Scan Test
Perform a scan test to determine if the scanner is work-
ing properly. Login as a regular user to perform the
scan test.
1. Load the documents to be test scanned.
⇒ The "Login" screen appears.
However, if the scanner is setup for automatic
login, the "Login" screen is not shown.
Proceed to Step 4.
2. On the "Login" screen, enter a "User Name"
and "Password".
Enter "guest" for the User Name and Password
fields.
3. Press the [Login] button.
⇒ If the user name and password are valid, the
"Main Menu" screen appears.
4. Select the [Maintenance] button on the "Main
Menu" screen.
⇒ The "Maintenance" screen appears.
5. Press the [Scan Test] button.
⇒ The scan settings information for the scan test
is displayed.
6. Press the [Scan] button.
⇒ Scanning starts. When the scan has completed,
the "Scan Viewer" opens.
Reverse
Side
fi-6010N Network Scanner Getting Started
16
7. Check the scanned data.
8. Press the [OK] button.
⇒ The "Maintenance" screen is shown again.
■ If Scanning Completes
Successfully
Continue with the setting procedures described in Chap-
ter 1 of the "Operator's Guide".
■ If Scanning does not Complete
Successfully
If the top cover is open
• Message
Top cover may be open. Close the top cover,
reload the documents and try again.
• Action
Close the top cover, and try the scan test again.
If no document is loaded
• Message
Document not found. Load a document into the
ADF, making sure the side guides are adjusted
correctly and try again.
• Action
Load a document, and try the scan test again.
If a multifeed is detected
• Message
Feed Error: Document(s) may not match the set
paper size, ADF may have grabbed more than
one sheet, or documents may not be suitable for
scanning. Remove the documents from the ADF,
check them and try again. If problem persists,
consult the manual.
• Action
Remove the document for which multifeed was
detected, and try the scan test again.
If a paper jam occurs
• Message
Paper jam has occurred. Remove the documents
from the ADF and try again.
• Action
If the "Scan Viewer" screen appears with par-
tially scanned data, just click the [OK] button.
Remove any unscanned documents from the
ADF. Open the scanner's top cover, remove the
jammed document from the scanner, and close
the scanner's top cover. From the "Maintenance"
screen, try the test scan again.
If a problem is detected with the scanner
• Message
Scanner initialization has failed. Try turning the
power off and back on again. The administrator
should contact the FUJITSU scanner dealer or
an authorized FUJITSU scanner service provider
for help.
• Action
Try the following:
• If the scanner does not restart automatically,
press the [Shutdown] button on the "Login"
screen to turn the power off, and turn the
power back on again to restart the scanner.
• If the error status persists after the scanner is
restarted, press the [Shutdown] button on the
"Login" screen, disconnect the AC cable
from the scanner to turn the power off, wait
for at least ten seconds, then reconnect the
AC cable and try turning the power back on
again. If the error status persists, contact
your FUJITSU scanner dealer or an
authorized FUJITSU scanner service
provider.
ATTENTION
To disable login with a guest
account, select [Off] for "Guest
Account" in the [System Settings]
screen on the [Login Settings] tab.
HINT
System settings or user data can be
backed up from the [User Data Store]
or [System Settings File] screen on
the [Maintenance] tab. This can only
be performed via the network
interface. Backup should be per-
formed regularly. This can only be
performed via the network interface
using the Admin Tool or Central Admin
Console.
For more details, refer to the "Opera-
tor's Guide".