Craftsman 917.28934 - Manual (Page 17)

TRACTOR
Always observe safety rules when performing
any maintenance.
BRAKE OPERATION
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be serviced. (See "TO CHECK
BRAKE" in the Service and Adjustments
section of this manual),
TIRES
• Maintain proper air pressure in all tires
(See PSl on tires).
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage.
NOTE: To seal tire punctures and prevent flat
tires due to slow leaks, tire sealant may be pur­
chased from your local parts dealer, Tire seal­
ant also prevents tire dry rot and corrosion.
OPERATOR PRESENCE SYSTEM AND
REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse
operation systems are working properly. If
your tractor does not function as described,
repair the problem immediately.
• The engine should notstart unless the brake
pedal is fully depressed, and the attachment
clutch control is in thedisengaged position.
CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt
by the operator to leave the seat without
first setting the parking brake should shut
off the engine,
• When the engine is running and the at­
tachment clutch is engaged, any attempt
by the operator to leave the seat should
shut off the engine.
■ The attachment clutch should never oper­
ate unless the operator is in the seat
CHECK REVERSE OPERATION (ROS)
SYSTEM
• When the engine is running with the ig nition
switch in the engine "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
shut off the engine,
• When the engine is running with the ignition
switch in the ROS "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
NOT shut off the engine,
Wm
BLADE CARE
For best resuits mower blades must be sharp
Replace worn, bent or damaged blades.
ACAUTION: Use only a replacement blade
approved by the manufacturer of your tractor
Using a blade not approved by the manu­
facturer of your tractor is hazardous, could
damage your tractor and void your warranty,
BLADE REMOVAL
1, Raise mower to highest position to allow
access to blades.
NOTE: Protect your hands with gloves and/
or wrap blade with heavy cloth.
2. Remove biade boit by turning counter­
clockwise ,
3 Install new blade with stamped "GRASS
SIDE" facing the ground.
IMPORTANT: To ensure proper assembly,
center hole in biade must align with star on
mandrel assembly,
4, Install and tighten blade bolt securely
(45-55 Ft. Lbs. torque).
IMPORTANT: Special blade boit is heat
Your tractor has a battery charging system
which is sufficient for norma! use. However,
periodic charging of the battery with an au­
tomotive charger will extend its life.
• Keep battery and terminals dean.
• Keep battery bolts tight,
• Keep small vent holes open,
• Recharge at 6-10 amperes for 1 hour.
NOTE:TheorigfnaIequipmentbatteryonyour
tractor is maintenance free. Do not attempt
to open or remove caps or covers. Adding or
checking level of electrolyte is not necessary,,
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals
can cause the battery to "leak” power.
1.
2
.
3.
5.
ROS "On" Engine "On" Position
Position (Normal Operating) 17
Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.
Rinse the battery with plain waterand dry.
Clean terminals and battery cable ends
with wire brush until bright.
Coat terminals with grease or petroleum
jelly.
Reinstall battery (See “REPLACING BAT­
TERY" in the Service and Adjustments
section of this manual).