Gradall 534B-9 Parts Manual - Manual (Page 185)

OPTIONAL EQUIPMENT
(9104-5129) Steer Axle Advantage Kit
FOR SERVICE ONLY
Original Issue 3-96
Revised 1-12-99
Item Part No. Qty. Description Of Part
31 9104-1450 AR SHIM (.0478 thick, see note #3)
32 9104-1451 AR SHIM (.106 thick, see note #3)
33 2 DRIVE HUB (use existing hubs )
34 9112-0004 1 R.H. STEERING KNUCKLE
35 8867-1008 2 LUBE FITTING, STRAIGHT, 1/4-28
36 8850-1006 2 HEX NUT, 3/8-16
37 8855-1011 6 LOCKWASHER, 3/8
38 8320-1144 2 HEX HD CAPSCREW, 3/8-16X5-3/4,
GR5
39 9108-1695 2 STEERING CYLINDER PIVOT PIN
(axle end)
40 8871-1280 2 HEX SOCKET PIPE PLUG, 1/8
41 9104-1598 AR SHIM (see note #2)
42 2 STEERING CYLINDER ASSY (see page
13-23 for details)
43 9108-1523 1 L.H. TUBE SUPPORT
9108-1522 1 R.H. TUBE SUPPORT
44 8820-1035 4 HEX HD CAPSCREW, 3/8-16X1, GR5
45 8821-1121 2 SOCKET HD CAPSCREW,
1/2-13X6-1/2, GR8
46 9112-0003 1 L.H. STEERING KNUCKLE
47 9104-3247 2 SELF-ALIGNING BUSHING
48 8867-1001 2 LUBE FITTING, STRAIGHT, 1/8
49 9104-1731 16 SPACER
50 12 HARDENED WASHER, 3/4 (use
existing hardware)
51 12 HEX HD CAPSCREW, 3/4-10X2 (use
existing hardware)
52 9116-6063 1 TIE ROD (includes item 47)
53 8852-1208 2 HEX LOCKNUT, 1/2
54 9104-3222 2 12 PT. SCREW, 3/4-10X2, GR8
(lubricate & torque to 270-290 ft. lbs.)
(see note #4)
55 9104-3494 2 12PT. SCREW, 5/8-1X2-1/4, GR8
(torque to 200 ft. lbs.) (see note #4)
56 9020-1918 AR SHIM (10 gauge thick, see note #2)
57 8855-1153 2 LOCKWASHER, 5/8
58 8821-2321 2 SLOT HD CAPSCREW,
5/8-11X3-3/4,GR8
59 2460-1570 2 LIP SEAL
60 9112-3031 2 BUSHING
61 9104-1489 2 BUSHING
62 8821-2321 2 SOCKET HD CAPSCREW,
5/8-11X3-3/4, GR8
63 8850-1110 2 HEAVY HEX JAM NUT, 5/8-11
Item Part No. Qty. Description Of Part
9104-5129 Ref STEER AXLE ADVANTAGE KIT
(includes all items except 33, 50 & 51)
9103-5240 1 STEERING KNUCKLE KIT (includes
items 2,4, 7 thru 14, 16 thru 22,
28 thru 32, 45, 53, 57 & 58 - one kit does
both sides)
9104-5152 Ref STEERING CYLINDER PIN KIT
(includes one each of items 1, 2, 3, 12 &
21 thru 24 - one kit needed for each side)
1 8852-1312 2 HEX LOCKNUT, 3/4-10 (torque to
160-175 ft.lbs.)
2 9108-1415 2 DIRT SHIELD
3 9104-1481 2 STEERING CYLINDER PIN (knuckle
end)
4 9112-1239 2 BUSHING
5 9104-1439 2 TIE ROD PIN
6 8852-1306 2 LOCKNUT, 3/8-16
7 9112-1240 4 BUSHING
8 9112-3030 4 BACK-UP RING
9 8859-1032 4 O-RING
10 9112-3027 2 BUSHING (lower)
11 9112-3029 2 O-RING
12 8859-1104 4 O-RING
13 9112-1091 2 THRUST BUSHING
14 9104-1733 AR SHIM
15 9104-6126 1 REAR AXLE WELDMENT
(includes items 10, 17, 60 & 61)
16 8692-1268 2 LIP SEAL
17 9112-3028 2 BUSHING (upper)
18 9108-1693 2 UPPER KING PIN
19 8858-1323 4 RETAINING RING
20 8867-1022 4 LUBE FITTING, 30 DEGREES, 1/8
21 9104-1732 AR SPACER
9104-1438 AR SPACER
22 8859-1019 2 O-RING
23 9104-1459 2 WASHER
24 8850-1416 2 HEX JAM NUT,1-14 (torque to
225-250 ft. lbs.)
25 8320-1140 2 HEX HD CAPSCREW, 3/8-16X2-3/4,
GR8
26 9103-3444 2 STREET ELBOW
27 9103-3445 2 LUBE FITTING
28 9114-1424 2 LOWER KING PIN
29 9104-1596 AR SHIM (20 gauge thick, see note #3)
30 9104-1449 AR SHIM (.060 thick, see note #3)
NOTE #1: CUSTOMER TO USE EXISTING WHEEL HUBS & HARDWARE, DRIVE MOTORS, DRIVE MOTOR
TUBE ASSEMBLIES, AND DRAIN LINE HOSES OR ORDER SEPARATELY IF REPLACEMENT IS REQUIRED.
NOTE #2: CYLINDER BASE END MUST BE FREE TO ROTATE. SHIM STEER CYLINDER BASE END AS
REQUIRED TO MAINTAIN A TOTAL MAX. GAP OF 1/16".
NOTE #3: SHIM BOTTOM KNUCKLES AS REQUIRED TO MAINTAIN NO MORE THAN
1/32" MOVEMENT. SHIM TOP KNUCKLES AS REQUIRED TO MAINTAIN NO MORE THAN 1/16" GAP. MUST
HAVE A MINIMUM OF ONE SHIM.
NOTE #4: ITEM 55 TO BE USED WITH FAIRFIELD HUBS ONLY.
13-22 PCN 971053, 971316, 980730 - JH * Revised illistration and parts list, also added note #4.