intimus Combishred - Manual (Page 5)

MAINTENANCE
5
COMPENSATION OF THE LIGHT BARRIER:
In order to eliminate malfunctions due to chan-
ging light conditions at the inlet aperture (e.g.
by changing the location) or due to the wear
of the fotocell (scratches), the sensitivity of the
light barrier is automatically
re-adjusted by the
machine for the detection of „normal“ paper in
regular intervals.
This so called „compensation“ can also be carried
out
manually in accordance with the sequence
described in the following (e. g. after change of
the light barrier or the PC Board).
The „receptacle full“ switch-off must not be ac-
tivated for the re-adjustment. The procedure is
as follows:
1. Switch off the maschine at the pushbutton switch
(1) and open the door.
2. Press the pushbutton switch „reverse“ (3) and
keep it pressed.
3. Press the „ready“ pushbutton switch (1).
4. Release the „reverse“ pushbutton switch (3)
after approx. 3 sec.
5. Push switching flap „receptacle full“ backwards
for at least 3 sec.
6. Close the door after approx. 3 sec.
7. Cover the light barrier with a piece of paper (do
not feed the paper up to the cutter) and wait
until the motor is switched on.
This completes the compensation. The machine
is now ready for operation.
Note: If the compensation process has been
interfered with due to exessive external incident
light (direct sun light, lamps, spots etc.) or due to
a false procedure, keep the external light away
from light barrier and re-start the compensation
process right from the beginning.
CLEANING THE PHOTOCELLS (fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
TECHNICAL DATA
MALFUNCTIONS
MATERIAL JAM IN MACHINE:
If too much material is fed in, causing a jam, the
machine will respond as follows:
- Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (6) (fig. 1) lights up.
Jam on the paper side (wide feed slot)
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(3) (fig. 1).
- The pilot lamp (6) (fig. 1) goes off.
- Remove excess paper from the machine and
continue shredding with less paper.
Jam of the data media side (narrow feed slot)
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(3) (fig. 1).
- The pilot lamp (6) (fig. 1) goes off.
- Activate the forward pushbutton (1) (fig. 1).
The material is once again fed to the cutting
system.
- If required, switch the cutting system alternately
to forward and reverse until all of the material
has been run through the cutting system and
shredded.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
the pushbutton switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the
plug connected to the mains?
Mains connection: 2-pole mains switch,
internal appliance plug,
separate power cord
- Is the pushbutton switch (1) on?
- Is the door closed?
- is one of the receptacles full?
The receptacle has to be emptied.
- is there a
material jam in the machine?
Follow the instructions under ”MATERIAL
JAM”
- has the motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
ACCESSORIES
PAPER SIDE:
Cutting width:
3.8x36 mm (cross-cut)
Cutting capacity: 20-22 sheets (70g/m 2 )
Working width: 260 mm
DATA MEDIA SIDE:
Type of shredding:
Particle or strip-cut
(depending
upon material)
Cutting capacity: 1 disk or cassette
at a time
Working width: 125 mm
GENERAL:
Supply voltage:
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/240V/50Hz:
10 amps (slow-blow)
120V/100V/50/60Hz: 20 amps (slow-blow)
Noise level: approx. 56 dB(A)
Power: 1.1 kW
Dimensions:
Width:
660 mm
Depth: 430 mm
Height: 930 mm
Weight: ca. 55kg
Description Order-No.
Plastic bag, 440 x 330 x 950 x 0,05 mm (paper side) 99977
Plastic bag, 345 x 310 x 750 x 0,17 mm (data media side) 83177
Lubricant, 125 ml bottle 99943
Note: For orders of special accessories and spare parts, please contact your dealer.
fig. 5
MAINTENANCE CUTTING BLOCK:
After approximately 15 minutes of continuous
use, run the cutting system in reverse for 15 to 20
seconds and spray some of the enclosed Special
Oil onto the cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (1) (fig. 1).
GB
2
CombiShred
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
DISPOSING