intimus Combishred - Manual (Page 4)

Never feed more than one disk or cas-
sette to the machine at once!
If more than one disk or cassette is in-
advertently fed to the machine, refer to
”MATERIAL JAM IN MACHINE” under
”MALFUNCTION”.
EMPTYING THE RECEPTACLES (Fig. 4):
The shredded material is being catched
separatly
in the two receptacles standing side by side. If one
of the two receptacles is full, the machine switches
off automatically. The pilot lamp (5) (fig. 1) lights
up. Empty the receptacle as follows:
- Open the door and pull out the receptacle (s)
a little. Take off the full plastic bag and dispose
of the contents.
- Insert the empty bag, move the receptacle (s)
back and close the door.
Note: The machine only runs with closed door!
SCOPE OF APPLICATION:
The
intimus CombiShred data shredder is a
machine for shredding general written material
and all types of data media, such as CDs, DVDs
and 3.5“ diskettes.
The right-hand side of the cutting me-
chanism (wide feed slot) must only be
used for shredding paper!
The left-hand side of the cutting me-
chanism (narrow feed slot) must only
be used for shredding CDs, DVDs and
3.5“ diskettes!
Any attempt to shred other types of data
medium may result in damage to the
machine (e.g. destruction of the cutting
mechanism etc.).
INSTALLATION:
- Unpack and set machine upright.
- Put a plastic bag in each receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“).
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
The fold-up material shelf (7) (fig.3) on
the door must not be used as a
step or seat. Risk of overturning the
machine!
FEEDING OF PAPER:
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Feed paper to the cutting mechanism through
the right-hand feed slot (wide slot).
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details.
Should the machine be overfed, refer to
„MATERIAL JAM IN MACHINE“ under
„MALFUNCTION“.
FEEDING DATA MEDIA:
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Feed the relevant data media (CDs, DVDs or 3.5“
diskettes) individually to the cutting mechanism
through the
left-hand feed slot (narrow slot).
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
CONTROLS:
1 = Pushbutton switch „ready“ (fig. 1)
Depress this switch to start the machine or
to stop the machine.
2 = Light barrier (forward operation) (fig. 2)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
3 = Pushbutton switch „reverse“ (fig. 1)
Pressing this button activates the cutting
mechanism into reverse.
4 = Pilot lamp „ready“ (fig. 1)
Lights when the pushbutton switch (1) is
operated.
5 = Pilot lamp
„receptacle full“ / „door open“ (fig. 1)
Lights when
a) the receptacle is full and needs to be
emptied. At the same time the machine
switches off automatically.
b) the door is not closed. The machine then
switches off automatically and it cannot be
started as long as the door is open.
6 = Pilot lamp “material jam“ (fig. 1)
lights if too much material is fed into the cutting
mechanism. The cutting mechanism halts,
then runs one step in reverse and stops. The
motor switches off.
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
IMPORTANT SAFETY NOTES
4
OPERATION
INITIATION
OPERATION
fig. 2 fig. 4 fig. 3
GB
fig. 1
2
7
4 6 1 3 5
CombiShred