Panasonic AJ-HD1700PE - Manual (Page 86)

86
Setup menus
The underlining (__) denotes the factory setting mode.
(continued)
No./Item Description of setting
118* 1
SP MODE
INH
For selecting whether to allow or inhibit
recording on a tape which has been written
by a format other than DVCPRO HD-LP.
0000 OFF:
Recording on the cassette tape is allowed.
0001 ON:
Recording on the cassette tape is inhibited.
• When 0 (OFF) has been selected, whether recording
on the cassette tape is allowed or inhibited is
determined by the setup menu item No.113 (REC
INH) setting.
• The recording format is determined by the setup
menu item No.020 (SYS FORMAT) setting.
131
PAGE MODE
For selecting what cue point operation is to
be performed when the multi cue function has
been set to ON.
0000 MANU:
Operation is confined within the selected page,
and 6 cue points can be registered.
0001 AUTO:
When the page whose cue points are being
registered
becomes full, operation is
automatically transferred to the next page, and
registration is continued. A total of 60 cue
points on up to 10 pages can be registered.
132
ROTA MODE
For selecting whether to perform the
registration operation if all the cue points
have already been registered when the multi
cue function has been set to ON.
0000 OFF:
No further cue points are registered.
0001 ON:
The registration operation is continued. If “MANU”
has been selected as the setup menu item No.131
(PAGE MODE) setting, the next cue point is
registered at CUE
¢ 1 on the page concerned; if
“AUTO” has been selected, it is registered at CUE01.
No./Item Description of setting
140* 1
OUTPUT
For selecting the output signals.
0000 EE:
:
The input signals selected by setup menu items
No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
to No.724 (D IN SEL 78) are output.
:
The input signals selected by setup menu items
No.600 (VIDEO IN SEL) and No.713 (CH1 IN SEL)
to No.724 (D IN SEL 78) are output:
0001
TAPE:
The signals played back from the tape are output.
:
The simultaneous playback signals are output.
In order to select the output signals during recording or
editing, set setup menu item No.302 (CONFI EDIT).
141* 1
VOLUME
For setting what is to be controlled by the
audio volume controls on the front panel.
0000 REC:
The controls function as REC volume controls.
0001 PB:
The controls function as PB volume controls.
0002 AUTO:
Normally, the controls function as PB volume
controls. However, during recording or in the
EE/INPUT CHECK status, they automatically
function as REC volume controls.
142* 1
AUDIO UNITY
For selecting the conditions under which the
AUDIO UNITY lamp on the front panel is to light.
0000 IN:
The lamp lights when all the audio input levels
are set to the UNITY level.
0001 OUT:
The lamp lights when all the audio output
levels are set to the UNITY level.
0002 IN/OUT:
The lamp lights when all the audio input and
output levels are set to the UNITY level.
143
CASSTT
LIGHT
For setting whether the lighting of the tape
mechanism is to be set to ON or remain OFF.
0000 OFF:
The mechanism does not light even when a
cassette is inserted.
0001 ON:
The mechanism lights when a cassette is inserted.
144
TC INPUT
For switching the preset registration method
for the time code.
0000 NORMAL:
The time code is input starting with the left-
most digit.
0001 REV:
The time code is input from the high-order digit
but is displayed from the right-most digit.
145
FRONT LCD
For selecting whether the LCD monitor display on
the front panel is to be turned on or off.
0000 OFF:
The display is turned off.
0001 ON:
The display is turned on or off in synchronization
with the screen saver operation for the time code
display area.
133
KEY BEEP
For setting the volume of the sound heard
when the keys are touched.
0000 OFF
0001 LOW
0002 HIGH
134
ALARM BEEP
For setting the volume of the alarm tone.
0000 OFF
0001 LOW
0002 HIGH
If the fan motor has shut down, the alarm tone is sounded
at the HIGH volume level regardless of this setting.
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.
116
EJECT LAMP
For selecting whether the EJECT lamp is to remain
lighted or go off after the cassette tape has been
ejected.
0000 MODE1:
The EJECT lamp remains lighted.
0001 MODE2:
The EJECT lamp goes off.