Marantz PD4292D User Manual
Page 13
7
RC2000MKII keypad and DIRECT function commands
will be configured for DSS (digital satellite system) con-
trol. We have included DSS commands within the
RC2000MKII’s pre-programmed memory for RCA
brand DSS equipment. If you have another brand of
DSS, you can “teach” the RC2000MKII with the re-
mote control codes of your equipment.
0 LCD window
The LCD window provides a wealth of information,
including function selection name, DIRECT function
names, learning and programming steps, as well as use-
ful indicators for battery status, and helpful indicators.
The LCD window features back-lighting, making it easy
to view when the room ambient light is very low.
A Volume up (+) and down (-)
Used to raise and lower the main system volume level.
Note that these buttons are clearly the largest size, and
are conveniently located and contoured for easy opera-
tion, even in low lighting.
B Ten keypad
Like a telephone key pad, the ten number buttons (0-9)
are used to enter numeric digits, useful for finding a
specific track on a CD, or to tune a pre-set radio station,
etc.
C MEMO
This button is used to program your CD player’s track
memory, or to enter a VCR recording program, and can
be used to provide the MEMO function included with
other components in your system.
D CLEAR
This button is used to cancel certain memory or pro-
gramming operations.
E Transport control functions
These buttons provide transport commands for your
source components, such as laser disc player, CD player,
VCR, audio tape deck, etc., and are dependent on the
function source selected. For example, when the
RC2000MKII is set to LD (laser disc) mode, the trans-
port keys will operate the laser disc player’s PLAY,
STOP, PAUSE, FAST FORWARD, FAST REVERSE,
NEXT and PREVIOUS track functions. Change the
RC2000MKII function selector to VCR, and these keys
will then operate the VCR’s transport command func-
tions, etc.
F CURSOR buttons
Some components feature menus that are navigated with
up, down, left and right direction commands. The cur-
sor buttons can be used to navigate within on-screen
menus, for components such as amplifier or receiver,
PD4292D, DSS/satellite tuner, etc. These buttons are
also used for certain RC2000MKII programming func-
tions.
G MUTE
For those components (such as amplifier or receiver, etc.)
with a mute function, this button can be used to mute
the sound temporarily.
H GUIDE
This button is intended for owners of DSS (digital sat-
ellite system) or similar equipment, to activate the on-
screen programming guide, used when changing chan-
nels etc.
I OSD (On Screen Display)
Some components, such as an amplifier or receiver,
PD4292D, etc., feature on screen display for operation
and/or programming. The OSD button can be used to
activate the on screen display, or turn it off if desired.
J LIGHTING
Press this button to activate the back-lit LCD screen and
back-lit keys independently SETUP mode. A quick
touch is all that is necessary. The back-lighting will
remain on for 3 seconds. If you wish, you can even re-
program the RC2000MKII to shorten or lengthen the
amount of time the back-lighting is activated when this
button is pressed.
K Channel up(▲), down(▼)
Press this button to change the tuner, DSS or VCR pre-
set channels to upward or downward.
L Transmitter window
Infrared signals will emanate from behind this window.
Simply aim the RC2000MKII towards the component(s)
you wish to control. You may find that the RC2000MKII
works fine when placed on a coffee table pointing to-
wards your A/V system components.
M Receiving window
Used when learning commands from other remotes, this
window is placed at the bottom of the RC2000MKII, so
that the two remotes are vertically oriented for easy trans-
fer of remote control information. Later in this guide
we will show you which of the RC2000MKII buttons
can be “taught” new commands from other components.
PD4292D-2
00.10.4, 3:10 PM
7