Hitachi SJ300 - Manual (Page 7)

1- 4
Function Mode
Code Function name SJ300 Setting range Initial data
-FE/-FU/-F Note
A061 1 s t frequency maximum limiter 0.00, 1 s t frequency lower limitter - maximum frequency(Hz) 0.00
A261 2 nd frequency maximum limiter 0.00, 2 nd frequency lower limiter-2 nd setting maximum frequency(Hz) 0.00
A062 1 s t frequency minimum limiter 0.00, start frequency-maximum frequency(Hz) 0.00
A262 2 nd frequency minimum limiter 0.00, start frequency-2 nd setting maximum frequency(Hz) 0.00
A063 Jump frequency1 0.00-99.99/100.0-400.0(Hz) 0.00
A064 Jump frequency Width 1 0.00-10.00(Hz) 0.50
A065 Jump frequency2 0.00-99.99/100.0-400.0(Hz) 0.00
A066 Jump frequency Width 2 0.00-10.00(Hz) 0.50
A067 Jump frequency3 0.00-99.99/100.0-400.0(Hz) 0.00
A068 Jump frequency Width 3 0.00-10.00(Hz) 0.50
A069 Acceleration stop frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A070 Acceleration stop time 0.00-60.0(s) 0.0
A071 PID selection 00(invalid)/01(valid) 00
A072 PID-P gain 0.2-5.0 1.0
A073 PID-I gain 0.0-3600.(s) 1.0
A074 PID-D gain 0.00-100.0(s) 0.00
A075 PID scale 0.01-99.99(%) 1.00
A076 PID feedback selection 00(feedback : OI)/01(feedback : O) 00
A081 AVR selection 00(ON always)/01(OFF always)/02(OFF on decelerating) 00/00/02
A082 Motor voltage selection 200/215/220/230/240, 380/400/415/440/460/480
(230/400)/
(230/460)/
(200/400)
A085 Operation mode selection 00(normal operation)/01(energy-saving operation)/02(Fuzzy) 00
A086 Energy-saving response-
accuracy adjustment 0.0-100.0 50.0
A092 Acceleration time2 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A292 Acceleration time2(2 nd motor) 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A392 Acceleration time2(3 rd motor) 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A093 Deceleration time2 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A293 Deceleration time2(2 nd motor) 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A393 Deceleration time2(3 rd motor) 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A094 2 nd stage adjustable selection 00(change with 2CH terminal)/01(change with setting) 00
A294
2 nd stage adjustable
selection(2 nd motor)
00(change with 2CH terminal)/01(change with setting) 00
A095 2 nd acceleration frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A295 2 nd acceleration
frequency(2 nd motor)
0.00-99.99/100.0-400.0(Hz) 0.00
A096 2 nd deceleration frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A296 2 nd deceleration frequency
(2 nd motor)
0.00-99.99/100.0-400.0(Hz) 0.00
A097 Acceleration pattern selection 00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve) 00
A098 Deceleration pattern selection 00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve) 00
A101 OI start 0.00-99.99/100.0-400.0(Hz) 0.00
A102 OI end 0.00-99.99/100.0-400.0(Hz) 0.00
A103 OI start rate 0.-100. (%) 20.
A104 OI end rate 0.-100. (%) 100.
A105 OI start selection 00(external start frequency)/01(0Hz) 01
A111 O2 start -400.--100./-99.9-0.00-99.9/100.-400.(Hz) 0.00
A112 O2 end -400.--100./-99.9-0.00-99.9/100.-400.(Hz) 0.00
A113 O2 start rate -100. - 100. (%) -100.
A114 O2 end rate -100. - 100. (%) 100.
A131 Acceleration curve constant 01(small swelling)-10(large swelling) 02
A132 Deceleration curve constant 01(small swelling-10(large swelling) 02
b001 Retry selection
00(trip)/01(0Hz start)/02(start after equal frequency)/
03(trip after equaling frequency and deceleration stop)
00
b002
Allowable under-voltage power
failure time
0.3-1.0(s) 1.0
b003 Retry wait time 0.3-100.(s) 1.0
b004 Instantaneous power failure/
under-voltage trip during stop 00(invalid/01(valid)/02(invalid during stop and deceleration by stop
command)
00
b005
Instantaneous power failure/
under-voltage retry time
selection
00(16 times)/01(free) 00
b006 Open-phase selection 00(invalid)/01(valid) 00
b007 Frequency setting to match 0.00-99.99/100.0-400.0(Hz) 0.00
Upper and lower
limiter,jump
frequency
PID control
AVR
Operation mode/ adjustable function
External frequency adjustment
Accel, Decel
Instantaneous power failure restart