Hafler SR2300 - Manual (Page 22)

– 20 –
1. Connect signal from source to CH B input.
2. Biamp/Stereo switch not active (Stereo/Mono switch
overrides this switch when in mono/70V/100V mode).
3. Move Stereo/Mono switch to 100V mode.
4. Select 100V load, both channels.
5. Connect parallel array of 100V transformer-equipped
speakers across the red terminals of the 5-way binding
posts. (1200W – SR2600, 600W – SR2300)
6. CH B input sensitivity controls 100V mono output level.
Amplifier will clip at 100Vrms level.
Power
70V 4 Ω
Load
2 Ω 100V 8 Ω
70V 4 Ω 2 Ω 100V 8 Ω
BIAMP STEREO CH A IN
—
+
300W 2 Ω – 8 Ω
Mono,70V,100V
CH B IN
CH A OUT
CH B OUT
+
— 300W 2 Ω – 8 Ω
—
+
600W
For 70V, 100V, or Mono
• Use CH B input
• Load across RED
terminals
• Set load switches to one
half load impedance
A Division of
Rockford Corp.
Tempe, AZ 85281
Made in the U.S.A.
S R 2 3 0 0 300 W Stereo, 2 Ω – 8 Ω
600W Mono, 70V,100V
(Mono) 250W 100V-120V~ 50-60Hz 250V T7A
Chassis Float
Audio GND
3
2 1 +
–
+ –
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
4 Ω – 16 Ω
100 Volt
Transformer
100 Volt
Transformer
Parallel Array
etc.
100V 70V 100V 70V
SR2300 SR2600
Power
70V 4 Ω
Load
2 Ω 100V 8 Ω
70V 4 Ω 2 Ω 100V 8 Ω
BIAMP STEREO CH A IN
—
+
300W 2 Ω – 8 Ω
Mono,70V,100V
CH B IN
CH A OUT
CH B OUT
+
— 300W 2 Ω – 8 Ω
—
+
600W
For 70V, 100V, or Mono
• Use CH B input
• Load across RED
terminals
• Set load switches to one
half load impedance
A Division of
Rockford Corp.
Tempe, AZ 85281
Made in the U.S.A.
S R 2 3 0 0
300 W Stereo, 2 Ω – 8 Ω
600W Mono, 70V,100V
(Mono) 250W 100V-120V~ 50-60Hz 250V T7A
Chassis Float
Audio GND
3
2 1 +
–
+ –
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
4 Ω – 16 Ω
70 Volt
Transformer
70 Volt
Transformer
Parallel Array
etc.
70 Volt
Transformer
70 Volt
Transformer
etc.
100V 70V
SR2600
1. Connect signal from source to both CH A and CH B inputs.
2. Move Biamp/Stereo switch to Stereo mode.
3. Move Stereo/Mono switch to Stereo mode.
4. Select 8
Ω
speaker load for each channel.
5. Connect parallel array of 70V transformer-equipped
speakers (up to 600W per channel) to 5-way binding
posts.
6. Adjust CH A and CH B level controls independently.
100V MONO MODE (SR2300/SR2600)
70V STEREO MODE (SR2600 ONLY)