Honeywell EXCEL 10 W7752D - Manual (Page 4)

EXCEL 10 FCU CONTROLLER LNS PLUG-INS USER GUIDE
EN2B-0285GE51 R0909 2
Products Covered
This System Engineering Guide describes how to apply the
Excel 10 FCU Controllers and the accessories to typical FCU
applications. The specific devices covered include:
• W7752D,E,F,G, and J FCU Controllers.
• W7754K,L,M,N, and P FCU Controllers.
• T7460 Wall Modules.
• T7560 Wall Modules.
Organization of Manual
The Introduction and Application Steps 1 through 5 provide
the information needed to make accurate ordering decisions.
Application Step 6 and the Appendices include configuration
engineering that can be started using a LNS tool after the
devices and accessories are ordered. Application Step 7 is
troubleshooting. Information provided in support of the use of
third-party LonWorks communication packages to configure
FCU Controllers is found in the Appendices.
The organization of the manual assumes a project is being
engineered from start to finish. If you are adding to, or
changing an existing system, the Table of Contents can guide
you to the relevant information.
Applicable Literature
The following is a list of documents that contains information
related to the Excel 10 FCU Controller. Form No.
Title
EN0B-0376GE51 Excel 10 W7752D,E,F,G,J FCU
Controller Specification Data
EN0B-0453GE51 Excel 10 W7754K,L,M,N,P FCU
Controller Specification Data
EN1B-0250GE51 Excel 10 W7752D,E,F,G,J FCU
Controller Installation Instructions
EN1B-0251GE51 Excel 10 W7754K,L,M,N,P FCU
Controller Installation Instructions
EN2B-0285GE51 Excel 10 FCU Controller LNS Plug-Ins
User Guide
74-3083 Excel 10 T7460 Wall Modules
Specification Data
95-7610 Excel 10 T7460 Wall Modules
Installation Instructions
EN0B-0237GE51 Excel 10 T7560 Wall Modules
Specification Data
EN1B-0146GE51 Excel 10 T7560 Wall Modules
Installation Instructions
95-7554 Excel 10 FTT/LPT 209541B Termination
Module Installation Instructions
Product Names
The W7752 Controller is available in five models:
• W7752D FCU Controller with 230 Vac power supply and
with relay suitable for reheat applications.
• W7752E FCU Controller with 230 Vac power supply
without reheat relay.
• W7752F FCU Controller with 115 Vac power supply with
reheat relay suitable for reheat applications.
• W7752G FCU Controller with 115 Vac power supply
without reheat relay.
• W7752J FCU Controller with 100 Vac power supply
without reheat relay.
The W7754 Controller is available in five models:
• W7754K FCU Controller with 230 Vac power supply, one
triac output, and one digital output suitable for attachment
to a solid-state relay employed for low-voltage Pulse-
Width Modulated (PWM) control in high-current electric
reheat applications.
• W7754L FCU Controller with 24 Vac power supply and
two triac outputs.
• W7754M FCU Controller with 230 Vac power supply.
• W7754N FCU Controller with 230 Vac power supply and
two triac outputs.
• W7754P FCU Controller with 230 Vac power supply, four
triac outputs, and an extra, fourth relay suitable for reheat
applications.
The FCU Controllers can use any of the following Excel 10
wall modules:
• T7460A with temperature sensor.
• T7460B with temperature sensor and setpoint adjustment.
• T7460C with temperature sensor, setpoint adjustment, and
bypass button and LED.
• T7460D with temperature sensor, setpoint adjustment and
5-position fan switch.
• T7460E with temperature sensor, setpoint adjustment,
bypass button and LED, and 3-position fan switch.
• T7460F with temperature sensor, setpoint adjustment,
bypass button and LED, and 5-position fan switch.
• T7560A with temperature sensor, unit enable button,
setpoint adjustment, bypass button, LCD display and
configurable fan override with up to five settings.
Other products:
• C7608A Return Air Sensor
Refer to the Table 15 (see Application Steps, Step 5. Order
Equipment) for complete listing of all available part numbers.