Remote control functions, 12 remote control functions – Harman-Kardon AVR 110 User Manual

Page 12

12 REMOTE CONTROL FUNCTIONS

Remote Control Functions

IMPORTANT NOTE: The AVR 110’s remote
may be programmed to control up to eight
devices, including the AVR 110. Before using the
remote, it is important to remember to press the
Input Selector button

e that corresponds to

the unit you wish to operate. In addition, the
AVR 110’s remote is shipped from the factory to
operate the AVR 110 and most Harman Kardon
CD or DVD players and cassette decks. The
remote is also capable of operating a wide vari-
ety of other products using the control codes
that are part of the remote. Before using the
remote with other products, follow the instruc-
tions on pages 27–29 to program the proper
codes for the products in your system.

It is also important to remember that many of
the buttons on the remote take on different
functions, depending on the product selected
using the Input Selectors

eg. The

descriptions shown here primarily detail the
functions of the remote when it is used to oper-
ate the AVR 110. (See page 30 for information
about alternate functions for the remote’s but-
tons.)

a Power On Button: Press this button to
turn on the power to a device selected by press-
ing one of the Input Selectors

b IR Transmitter Window: Point this win-
dow towards the AVR 110 when pressing buttons
on the remote to make certain that infrared com-
mands are properly received.

c Program Indicator: This LED indicator is
used to guide you through the process of pro-
gramming the remote. (See page 27 for infor-
mation on programming the remote.)

d Power Off Button: Press this button to
place the AVR 110 or a selected device in the
Standby mode.

e Input Selectors: Pressing one of these
buttons will perform three actions at the same
time. First, if the AVR 110 is not turned on, this
will power up the unit. Next, it will select the
source shown on the button as the input to the
AVR 110. Finally, it will change the remote con-
trol so that it controls the device selected. After
pressing one of these buttons you must press
the AVR Selector button

f again to oper-

ate the AVR 110’s functions with the remote.

f AVR Selector: Pressing this button will
switch the remote so that it will operate the
AVR 110’s functions. If the AVR 110 is in the
Standby mode, it will also turn the AVR 110 on.

g AM/FM Tuner Select: Press this button to
select the AVR 110’s tuner as the listening
choice. Pressing this button when the tuner is
already in use will select between the AM and
FM bands.

h Test Button: Press this button to begin
the sequence used to calibrate the AVR 110’s
output levels. (See page 18 for more information
on calibrating the AVR 110.)

i Sleep Button: Press this button to place
the unit in the Sleep mode. After the time
shown in the display, the AVR 110 will auto-
matically go into the Standby mode. Each press
of the button changes the time until turn-off in
the following order:

Note that this button is also used to change
channels on your TV when the TV is selected.

When the AVR 110 remote is being programmed
with the codes to operate another device, this
button is also used in the “Auto Search” process.
(See page 27 for more information on program-
ming the remote.)

jSurround Mode Selector: Press this
button to begin the process of changing
the surround mode. After the button has
been pressed, use the

⁄

buttons

to select the desired surround mode. (See page
23 for more information.) Note that this button
is also used to tune channels when the TV is
selected using the device Input Selector
e. When the AVR 110 remote is being pro-
grammed with the codes of another device, this
button is also used in the “Auto Search”
process. (See page 27 for more information on
programming the remote.)

k Night Mode: Press this button to activate
the Night mode. This mode is available in spe-
cially encoded digital sources, and it preserves
dialog (center-channel) intelligibility at low
volume levels.

l Channel Select Button: This button is
used to start the process of setting the AVR 110’s
output levels to an external source. Once this but-
ton is pressed, use the

⁄

buttons

mq to

select the channel being adjusted, then press the
Set button

o, followed by the

⁄

buttons

mq again, to change the level setting. (See
page 18 for more information.)

⁄

Button: This multipurpose button is

used to change or scroll through items in the on
screen menus, or to change configuration set-
tings such as output levels. When changing an
item such as the surround mode or digital input
directly, first press the function or mode to be
changed (e.g., press the Surround Mode

to select a surround mode or the Digital button
p to change the digital input) and then press
this button to scroll through the list of available
choices.

‹

Button: This button is used to change

the menu selection or setting during some of
the setup procedures for the AVR 110.

o Set Button: This button is used to enter
settings into the AVR 110’s memory. It is also
used in the setup procedures for delay time,
speaker configuration and channel output level
adjustment.

p Digital Select: Press this button to assign
one of the digital inputs gh

$ to a source.

(See page 23 for more information on using
digital inputs.)

Button: This multi-purpose button is

to select a surround mode or the Digital button
p to change the digital input) and then press
this button to scroll through the list of available
choices.

r Numeric Keys: These buttons serve as a
ten-button numeric keypad to enter tuner preset
positions. They are also used to select channel
numbers when TV has been selected on the
remote, or to select track numbers on a CD,
DVD or LD player, depending on how the
remote has been programmed.

s Tuner Mode: Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so that the AUTO indicator

V goes

out, pressing the Tuning buttons

u8 will

move the frequency up or down in single-step
increments. When the FM band is in use, press-
ing this button when a station’s signal is weak
will change to monaural reception. (See page
25 for more information.)

min

OFF