beautypg.com

Trilogy™ manual 1.1 – Hughes & Kettner TrilogyTM User Manual

Page 6

background image

1.4 Lead Channel
Articulate distorted tone plays a pivotal role in most players’
decision to buy an amp. A chief criterion for a top-notch guitar
amp is its ability to retain the guitar’s character and deliver
defined tone even with the GAIN knob cranked. Trilogy™
does this; what’s more, its LEAD sound is an excellent
vehicle for classic rock leads and crashing power chords.

1.5 Ultra Lead Channel
Dive into a deep reservoir of distortion and let powerful
sonic waves wash over you with every head-banging riff.
The ULTRA GAIN channel delivers American-style high-gain
tone with trouser leg-flapping low end and plenty of top-end
slice. Hot and bad, this channel’s distorted tone is what the
good doctor ordered for nu-metal and drop-D styles. It also
serves up sumo-sized lead tone for all other genres.

Handling:

LEAD-GAIN:

Controls the amount distortion in
the LEAD channel

ULTRA-LEAD-GAIN: Controls the amount distortion in

the ULTRA LEAD channel

MASTER:

Controls the volume level

BASS:

Controls the amount of bass frequencies
in both channels

MID:

Controls the amount of midrange fre-
quencies in both channels

TREBLE:

Controls the amount of treble frequen-
cies in both channels

LEAD ON:

Activates the LEAD channel (for a lean,
mean classic British tone)

ULTRA LEAD ON:

Activates the ULTRA LEAD channel (for
chunky American sounds)

1.6 Master Section
The master section lets you dial in Trilogy™’s overall output
level, control presence, route effects and adjust the dry/wet
balance, as well as “teach” the amp to respond to MIDI
program change messages.

Handling:

FX-MIX, FX ON and SERIAL

SmartLoop™ is a special effects routing circuit offering a
switchable parallel/serial effects loop. In parallel mode,
(SERIAL is deactivated) the processed signal is added to
the original signal of the preamp. Twist the FX-MIX knob to
adjust the dry/wet balance, that is, the ratio of unprocessed
to processed signal. Generally the best results are achieved
by programming or setting the signal processor’s output to
100% so that only the wet effected signal and no dry signal
is patched out of the effect device.

In serial mode (SERIAL is activated), SmartLoop™ works like a
conventional serial effects loop. This means you must adjust
the wet/dry balance on the signal processor.

Tip:
If you have not inserted an effect device into the FX loop, you
can use this circuit for a variety of other purposes:
• In parallel mode, you can use the RETURN jack to connect

a second instrument or any other audio source, and then
blend its signal with the guitar signal using the FX MIX knob.
You can also route the amp’s signal to a second power amp
or through a RED BOX

®

to a mixing console.

• When in serial mode and bridged (SEND and RETURN jacks

are connected using a cord equipped with 1/4" jack plugs),
the effects loop can serve as a second master preset that
may be activated for each channel via a footswitch. Use the
FX-MIX knob to adjust the volume level.

x

Note:

Be sure to connect a signal processor when the effects loop
is configured in serial mode. Otherwise, the signal chain is
interrupted and you will not hear your guitar’s signal!

PRESENCE

This knob determines the overtone content for all channels.

MASTER

As its name would indicate, this knob puts you in charge of
the EL-34 power amp tubes and the100 watts of power they
put out. Though this knob promises tons of tweaking fun, plea-
se exercise restraint and caution.

MIDI LEARN

Assigns the given amp settings to a MIDI program number
and serves to determine the amp’s basic MIDI configuration.
For more on this, see section 4 – MIDI.

1.7 Mains and Standby Switches

MAINS ON/OFF

This button switches the main power supply on and tubes the
opportunity to warm up for the work ahead.

STANDBY

This switch controls the high voltage power supply to the
tubes. When engaged, anode voltage is applied to the tubes'
filaments only so that the tubes remain warm and ready to
rock. When taking a short break from playing, please use
STANDBY rather than ON/OFF so the tubes remain at operating
temperature.

Trilogy™ Manual 1.1

6