Samson Concert 88 Camera Combo UHF Camera Wireless System (D: 542 to 566 MHz) - Manual (Page 35)

35 Système sans fil Concert 88
ENGLISH
FR
ANÇ
AIS
DEUT
SCHE
ESP
AÑOL
IT
ALIANO
Configuration rapide - Installation d'un seul système
L'émetteur étant hors tension, mettez en place deux piles AA neuves dans le clip de
ceinture CB88 ou dans l'émetteur portatif CH88. Laissez le logement à piles ouvert.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
Mettez l'émetteur sous tension (Marche) en maintenant l'interrupteur Power (Marche/
Arrêt) enfoncé ; le témoin LED s'allumera en vert.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter