Avago Technologies LSI SAS 3080X-R User Manual
Page 2
Version 1.0, December 2007
Find a list of LSI Corporation’s U.S. distributors, international distributors, sales offices, and design resource centers on the LSI web site
at:
LSI and the LSI logo are trademarks or registered trademarks of LSI Corporation or its subsidiaries. All other brand and product names may be
trademarks of their respective companies.
LSI Corporation reserves the right to make changes to the product(s) or information contained herein at any time without notice. LSI Corporation
does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly
agreed to in writing by LSI Corporation; nor does the purchase, lease, or use of a product or service from LSI Corporation convey a license under
any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Corporation or of third parties.
Corporate Headquarters
Website
Milpitas, CA
www.lsi.com
800-372-2447
Document Number: DB11-000077-00
Copyright © 2007 LSI Corporation
All Rights Reserved
6.
Replace the cover, the power cord(s) and power-up the system. Replace the system’s
cover, reconnect the power cord(s) and any network cables. Turn power on.
The LSISAS3080X-R hardware installation is complete and you are ready to install the operating
system drivers.
W I N D O W S D R I V E R I N S T A L L A T I O N
To load the
SYMMPI.SYS
miniport driver during a new Windows 2000 or Windows XP system
installation or to load the
LSI_SAS.SYS
driver during a new Windows 2003 system installation,
you can boot directly from the Microsoft installation CD-ROM. The Windows drivers are not
interchangeable; however, the instructions are similar.
To install a new Windows operating system and its appropriate device driver, follow these steps:
1.
Using another computer, copy the appropriate driver files supplied on the LSI Logic
Device Drivers & Utilities CD onto a diskette. This diskette is needed in Step 6. To create
the driver diskette, open the driver folder on the CD, and then open the folder for the
version of Windows to be installed on the new system. Next, select all folders and files
within the directory and copy them to the root directory of a clean floppy diskette.
2.
Boot the computer from the Windows CD-ROM.
3.
Press F6 when the words
Setup is inspecting your computer's hardware
configuration
appear, or when the Windows operating system prompts you for
nonsupported drivers.
NOTE:
You must press F6 for the new driver to be recognized. Otherwise, the system does not
recognize the devices controlled by the driver during the Windows setup.
4.
Follow the instructions until a screen displaying the words
Setup could not
determine the type of one or more mass storage device
appears.
5.
Choose S to specify additional devices.
6.
Follow the prompts and insert the Windows driver diskette when you are prompted to
insert the hardware support disk. Select the driver version appropriate for your system.
7.
Follow the Windows installation procedure to complete the installation. Microsoft
provides documentation with its installation CD-ROM.
NOTE:
Refer to the Fusion-MPT Device Management User’s Guide for detailed configuration and
installation instructions for all firmware and drivers.
L I N U X D R I V E R I N S T A L L A T I O N
Consult the Linux
ReadMe.txt
file on the
LSI Device Drivers & Utilities CD. LSI Logic
provides Open Source Drivers that may be
implemented in the following ways:
• Adding precompiled binaries to an
existing installation using driver update
disks or RPMs for selected distributions.
• Adding or updating the Fusion-MPT
source in the Linux kernel for any
distribution.
T E C H N I C A L S U P P O R T
For assistance installing, configuring, or
running the LSI22320SE, contact LSI
Technical Support:
E-mail: [email protected]
Phone: 1-800-633-4545 (North America)
+44.1344.413.115 (Europe)
Web Site: