Whelen OR650PGE User Manual

Aviation

Page 1

ENGINEERING COMPANY INC.

3.85

1.92

(REF)

6.0” ± 1.0”

(20 AWG,

MIL-22759/43)

AMP 350780-1
Connector
(w/Contact
AMP 350547-1)

.67

WIRING CHART

White

28VDC ACL

Pos. 3

Orange

28VDC POS

Pos. 1

Yellow

SYNC

Pos. 4

Black

Ground

Pos. 2

1.67

.500

SUGGESTED MOUNTING DETAIL

1.340

Area

To Be

Removed

2.500

.740

.630

.670

1.000

51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: [email protected]

Aviation

Installation Guide:

Aviation model(s) OR650PGE, OR650PRE

P/N 01-0790701-P1, 01-0790701-P2

Orion 650E

Wingtip Position/Anti-Collision Lighthead

SPECIFICATIONS:
Nominal Operational Voltage: ......................... 28VDC
(Operational from 22-32 VDC)
Input Current:
Position Lights................................................. 0.15 Amps
Anti-Collision Light (Avg.)................................ 0.35 Amps
Anti-Collision Light (Pulse) .............................. 1.8 Amps
Flashrate ......................................................... 45 ± 5 FPM

EQUIPMENT LIMITATIONS:
An approved forward position lighting system consists of three lights,
one located on the tail and one located on each wingtip. Model
OR650( )E is a wingtip position and anti-collision light.The assembly
should be mounted as far outboard on the aircraft as practical. The
baseplate must be mounted parallel to the vertical and horizontal
centerlines of the aircraft to project the patterns properly. This
assembly must be mounted behind a clear lens.
Certain types of installations may require additional testing.

CONTINUED AIRWORTHINESS:
The forward position light is designed with green or red LEDs. The
anti-collision light is designed with 24 white LEDs. If any one LED fails,
the unit must be repaired or replaced.
Note: To reduce eye strain, use an optical filter such as dark glasses
or a blue covering dome during LED inspection.

INSTALLATION PROCEDURES:
The following information is to assist you in installing a Whelen light
system.

Choose the appropriate light assembly.

Using the mounting detail information provided, prepare the
aircraft for means to secure the light assembly.

Carefully remove the #4 phillips head screw (qty. 4). Remove the
light assembly from the baseplate. CAUTION! Do not touch the
LED with either fingers or sharp objects. This could soil and/
or damage the lens and affect the optical performance of the
LEDs.

Using the appropriate hardware install the baseplate to the
aircraft.

Route the wires through the opening in the baseplate. Connect
the light inputs according to the chart shown. Connect the power
lead to an appropriately sized breaker. Connections to be
according to FAA approved methods.
Note: SYNC is a low-power, bi-directional control signal.
Connecting to the synchronize signal of any Whelen LED anti-
collision assembly to another Whelen anti-collision assembly will
cause the lights to flash at the same time. If Synchronization is
not necessary, the connection may be left open.

Re-install the light assembly on to the baseplate and insure that
all leads are clear of any obstructions and secured as required.

Check all avionics systems for interference from this installation.

A flight check should be performed by a properly certified pilot.

Update aircraft records, complete Form 337 and obtain FAA field
approval for installation, if required.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this article are minimum
performance standards. It is the responsibility of those installing this article either on
or within a specific type or class of aircraft to determine that the aircraft installation
conditions are within the TSO standards. TSO articles must have separate approval
for installation in aircraft. The article may be installed only if performed under 14 CFR
part 43 or the applicable airworthiness requirements.

TSO-C30c

TYPE I & II;

APPROVED

TSO-C96a

CLASS II;

APPROVED

This manual is related to the following products:

OR650PRE