Whelen 9040001 - Manual

Page 1
®
ENGINEERING COMPANY INC.
2.06
(LENS
HEIGHT)
2.22
3.28
1.11
3.59
.10
MOUNTING
SCREWS
Models
9040001, 02, 03, 04
Shown
.30
3.50
6.60
AMP 1-480425-0 HOUSING,
4 POS. HOUSING
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: [email protected]
Aviation
Installation Guide:
Aviation model(s): 9040001,02,03,04,11,12,21,22
P/N: 01-0790400-01, -02, -03, -04,
-11, -12, -21, -22
LED Position/Anti-Collision/Tail Light Ass’y
©2009 Whelen Engineering Company Inc.
Form No.14316A (032112)
SPECIFICATIONS:
Nominal Operational Voltage:.................. 14VDC / 28VDC
(14V Operation from 11V - 16V / 28V Operation from 22V - 32V)
Input Current:
LED Forward Position Light ........................ 0.25 Amps (Red)
0.21 Amps (Green)
LED Anti-Collision Light ([email protected] sec) . 7.2 Amps/4 Amps
LED Anti-Collision Light (Average) ............. 1.3 Amps/0.75 Amps
LED Tail Position Light................................ 0.25 Amps/0.25 Amps
Flashrate: .................................................. 45± 5 per min.
Total Weight: ............................................. 1.0 lbs.
EQUIPMENT LIMITATIONS:
An approved lighting system consists of two lights, one located on
each wingtip. The baseplate must be mounted parallel to the
vertical and horizontal centerlines of the aircraft to project the
patterns properly. A separate flasher unit is required per light.
NOTE: Certain types of installations may require additional testing.
CONTINUED AIRWORTHINESS:
The forward position light is designed with 3 LED’s. The tail
position light is designed with 3 LED’s. The Anti-Collision light is
designed with 26 LED’s. If any one LED fails, the unit must be
repaired or replaced. Inspect the lens. Replace if there is
excessive scratching, pitting, discoloration or cracking. NOTE: To
reduce eye strain, use an optical filter such as dark glasses or a
blue covering dome during LED inspection.
Note: The anti-collision light will automatically shut-off after 9-10
flashes if a failure is detected.
INSTALLATION PROCEDURES:
The following information is to assist you in installing a Whelen
Anti-Collision / Position light system.
1. Choose the appropriate Model 90400( ) replacement light
assembly.
2. The installation procedure described in the following text will
be confined to a single light installation, but is identical for
multiple light installations.
3. Connect the anti-collision inputs and the position light
inputs according to the chart shown. Connections to be in
accordance with FAA approved methods.
4. Using appropriate hardware, install light assembly and
insure that all leads are clear of any obstructions and ty-
rap as required. Secure light assembly, using vibration
resistant threaded fasteners.
5. Reinstall the lens.
6. Check all avionics systems for interference from this
installation.
7. A flight check should be performed by a properly
certified pilot.
8. When necessary, waterproof the light base to aircraft.
Apply single part silicone (RTV) or equivalent around
any open area where water could get in.
9. Update aircraft records, complete Form 337 and obtain
FAA field approval for installation, as necessary.
MADE IN THE U.S.A.
The conditions and tests required for TSO approval of this
article are minimum performance standards. It is the
responsibility of those installing this article either on or
within a specific type or class of aircraft to determine that
the aircraft installation conditions are within the TSO
standards. TSO articles must have separate approval for
installation in aircraft. The article may be installed only if
performed under 14 CFR part 43 or the applicable
airworthiness requirements.
TSO-C30c
TYPES I , II & III;
APPROVED
TSO-C96a CLASS II;
APPROVED