Whelen 7101101 - Manual

Page 1
Models:
7101101
7101102
Model:
7101103
Model: 7101101
Model:
7101101
Model:
7101102
Model:
7101103
Models: 7101102, 7101103
(Model 7101102 shown for reference)
2.17
1.71
.855
4.72
2.45
.95
3.36
1.36
1.71 1.71
1.36
3.46
2.00 2.10
8.00"±1.00"
Mounting Detail
Drain Hole
(TYP 2 PLCS)
Drain Hole
(TYP 2 PLCS)
20AWG Teflon Wire
Per MIL-W-22759/43
.95 Square
Position 1 = 28VDC (White)
Position 2 = Ground (Black)
D38999/20FA98PN Connector
Position A = 28VDC
Position B = Ground
Position C = N/C
1.750
1.750
.875
1.750
.875
.875
Ш1.30
Ш1.225
Ш1.225
2 x Ø.125
2 x Ø.125
2 x Ø.125
Square
2 x 4-40 x 5/8 MS51957-18
Mounting Screws
2 x 4-40 x 5/8 MS51957-18
Mounting Screws
The conditions and tests required for TSO approval of this
article are minimum performance standards. It is the
responsibility of those installing this article either on or
within a specific type or class of aircraft to determine that
the aircraft installation conditions are within the TSO
standards. TSO articles must have separate approval for
installation in aircraft. The article may be installed only if
performed under 14 CFR part 43 or the applicable
airworthiness requirements.
®
ENGINEERING COMPANY INC.
Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: [email protected]
Aviation
Installation Guide:
Models 7101101, 7101102, 7101103
P/N: 01-0771011-01, 01-0771011-02,
01-0771011-03
LED Tail Position
Light Assembly
©2005 Whelen Engineering Company Inc.
Form No.13992B (061008)
TSO-C30c
TYPE III
APPROVED
MADE IN THE U.S.A.
OPERATING INSTRUCTIONS:
Nominal Voltage: . . . . . . . . . . . .28 VDC
Operational Voltages: . . . . . . . .22 - 30 VDC
Input Current:. . . . . . . . . . . . . . .0.3 Amps
EQUIPMENT LIMITATIONS: The approved tail position
light assembly should be mounted vertically and as far aft
on the aircraft as possible, on a thermally conductive
surface
CONTINUED AIRWORTHINESS: The LED tail position
light assembly is designed with 6 LED’s. If any one LED
fails, the unit must be repaired or replaced. Inspect the
lens. Replace if there is excessive scratching, discoloration
or cracking.
INSTALLATION PROCEDURES: The following
information is to assist you in installing a Whelen tail
position light.
1. Choose the appropriate model light assembly which
is most applicable to your aircraft.
2. Remove the old light, locate and save the existing
+28VDC lead and (-) ground lead (7101102 &
7101103). Clean and prep ends as required.
3. Use the existing mounting holes and hardware.
4. For model 7101101, secure the existing connector
onto the base of the light assembly. For models
7101102 & 7101103, connect the existing +28 VDC
lead to the white 20 AWG lead on the input cable
assembly (supplied with light assembly). Connect the
existing ground lead to the black 20 AWG wire on the
input cable assembly. If a chassis ground wire exists
on the aircraft, connect it to the chassis ground wire
assembly. Both leads must be connected by FAA
approved techniques using approved hardware.
5. Make sure the existing system is equipped with an
appropriate sized breaker.
6. Remove two #4-40 screws from tail light assembly.
Save these screws.
7. Install the light assembly and insure that all the leads are clear
of any obstructions and ty-wrap as required. Secure light
assembly using approved vibration resistant hardware methods.
Note “Top” marking on the unit.
8. Re-mount the lens and retainer onto the assembly. Attach the
lens and retainer with mounting screws (provided).
9. Check all avionics systems for interference from this installation.
10. When waterproofing the assembly to the aircraft, apply aviation-
approved single part silicone (RTV) or equivalent around the
periphery with caution. Do not fill the drain holes at bottom of
unit. RTV should never be used between the rear surface of
the light assembly and its mounting surface.
11. Update aircraft records, complete Form 337 and obtain FAA
field approval for installation.
Model Shown:
7101102