Sealey FH2010 - Manual

1.1. ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an
RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a
qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1.
and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none are
loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Have
any faulty item immediately repaired or replaced by a qualified electrician. When a
BS1363/A 3 pin plug is damaged, cut the cable just above the plug and dispose of the
plug safely. Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have
been connected correctly, that the cable outer insulation extends beyond the
cable restraint and that the restraint is tight. Double insulated products, which are always marked with this symbol ,
are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as indicated above. DO NOT connect
either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a
qualified electrician to ensure that a suitably rated supply is available. We recommend that you discuss the
installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD
fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be
at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm² section cable.
InSTRUCTIonS FoR:
FAN HEATER 2000W 2 HEAT SETTINGS with
THERMOSTAT
moDEl no:
FH2010.V2
1.2. GENERAL SAFETY

WARNING! Disconnect the heater from the mains power, before servicing or performing any maintenance. Servicing or
maintenance must only be carried out by an authorised service agent.
 Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
 WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.
 DO NOT allow any untrained or incompetent persons use the heater. Ensure they are familiar with the controls and
hazards of the heater
 DO NOT allow children to touch or to operate the heater
 DO NOT obstruct the air inlet or outlet on the heater.
 DO NOT cover the heater.
 DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT touch the heater casing or grill when first switched off as these are hot and will take time to cool.
 DO NOT use the heater for anything other than its intended purpose. It is not suitable for drying clothes or laundry.
 DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
 DO NOT get the heater wet or use in areas of high condensation.
 DO NOT place the heater up against any surface such as a wall, door or furniture etc.
 DO NOT place the heater immediately below any electrical outlet.
 DO NOT allow the power lead to lie in front of the heater outlet.
 DO NOT attempt to repair a damaged heater, contact an authorised service agent.
 DO NOT stand on the heater.
 DO NOT connect the fan heater to a timer device or other equipment that can automatically switch the heater on or off.
 Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
1. SAFETY INSTRUCTIONS
FUSE RATING 13 AMP
Original Language Version FH2010.V2 Issue: 2(l) - 24/07/14 © Jack Sealey limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.