Sealey CH28110VS User Manual
Safety instructions
1.1
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1 and 1.1.2
end use a Portable Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none are loose.
1.1.6
Important: Ensure that the voltage marked on the appliance matches the power supply to be
used (110volt 32amp).
1.1.7
DO NOT pull or carry the appliance by the power cable.
1.1.8
DO NOT pull the plug from the socket by the cable.
1.1.9
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item
repaired or replaced by a qualified electrician. When a BS EN 60309 plug is damaged, cut the
cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions:
a) Connect the GREEN/YELLOW earth wire to the earth terminal.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that
the restraint is tight.
1.2
GENERAL SAFETY INSTRUCTIONS
Familiarise yourself with the applications and limitations of the heater.
Ensure
that heater body is positioned on a firm, horizontal dry surface.
Keep away
from flammable objects/materials/surfaces. This product gets very hot during use. Use in a location where accidental contact
(particularly by children) is unlikely.
Ensure
on/off switches are set to ‘off’ before connecting power cord to power supply.
Ensure the heater is in good order and condition before use. If in any doubt do not use the unit and contact an electrician.
Only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your warranty.
Check that element guard is in place, undamaged and firmly attached.
Keep tools and other items away from the heater when it is in use.
Keep the work area clean and clear of unnecessary items.
Keep children and unauthorised persons away from the heater, as it gets
very hot.
Disconnect from mains and allow to cool before moving or attempting any cleaning or maintenance.
DO NOT get the heater wet or use in damp or wet locations or areas where there is condensation.
DO NOT locate the heater below the power outlet.
DO NOT remove plug from mains supply by pulling on power cord.
DO NOT move the heater whilst in operation or even when still warm.
DO NOT touch the heater elements, even when cold.
Always
switch off heater, disconnect from power supply and allow cooling for at least
one hour before attempting to touch heater cassette.
DO NOT remove safety guard whilst heater is switched on. Turn off and allow cooling (as above) before servicing.
DO NOT disassemble the heater for any reason. The heater must be checked by qualified personnel only.
DO NOT use this product to perform a task for which it has not been designed.
DO NOT operate heater without safety guard or elements installed.
WARNING! If supply trips at consumer unit, ensure the correct rating of supply and appliance. If further tripping occurs consult
a qualified electrician.
DO NOT place any object on the safety guard of the heater cassette at any time.
WARNING! Ensure the heater is at least 2m from any object.
DO NOT leave unattended.
When not in use, store the heater carefully in a safe, dry, childproof location.
1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR:
STANDING CERAMIC HEATER
1.4/2.8KW 110V
MODEL N
O
:
CH28110VS
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
© Jack Sealey Limited
CH28110VS Issue: 2(l) - 12/06/15
Blue
(N)
Brown
(L)
Yellow/
Green
(E)
Cable
restraint