Sealey EH2001 - Manual (Page 2)

4.1. Position heater in an upright position on a firm surface and at a safe distance from any obstructions, flammable substances etc. Keep to a
minimum of 0.5mtr clearance at the rear and sides, and 2mtr clearance at the front.
4.2. Connect the heater to a suitable mains supply.
4.3. Set the thermostat dial to its maximum setting (fully clockwise).
4.4. The heater will switch on when the power setting dial is set to the heater setting.
NOTE: It will take up to three minutes for the heater to reach optimum temperature.
4.5. Once the room reaches the required temperature, turn the thermostat dial slowly counter-clockwise until the thermostat clicks, leave the
dial in this position to maintain the room temperature at this setting. The heater will continue to operate until the power switch is turned to
the OFF position.
4.6. For fan only operation, turn the power/fan selector to the fan only setting, and set the thermostat to its minimum setting.
4.7. When not in use, disconnect the heater from the mains supply. Store it in a safe, dry, childproof location.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EH2001
Voltage:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Power Rating:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000W
Heat Setting:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000W
Dimensions (W x D x H): . . . . . 215mm x 230mm x 280mm
Fuse Rating: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13A
Fan only setting
OFF
Power / Fan
Selector Thermostat
Power setting (2000W)
fig.1
EH2001 Issue: 4(L) - 29/04/15
IMPORTANT! This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the front of the
heater will be warmer than the general temperature of the room, but there may not be a significant increase due to the large volume of air passing
over the element. For the same reason, the element is hot during operation, but does not visibly glow. The room temperature depends on room size,
insulation and the ambient temperature, which will increase as the room gets warmer.
Electric fan heater for industrial applications. One heat setting with thermostat control, plus fan only setting. A totally dry heat with no
condensation, no gas, no fumes, so no smell. Ideal for workshops, garages etc.
WARNING! Before attempting any maintenance, ensure that the unit is unplugged from the mains power supply and that it has cooled down.
5.1. Clean the heater with a soft dry cloth only. DO NOT use abrasives or solvents.
5.2. Periodically check the heater grille to ensure that it is not blocked.
No other maintenance is necessary. If a problem with the heater is experienced, or if the power lead or plug is damaged, contact your
local authorised service agent for repair. DO NOT dismantle or tamper with the heater, as this may be dangerous and will invalidate the
warranty.
NOTE: It may take up to three minutes for the heater elements to reach optimum temperature. This is normal and not a fault.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or phone 01284 757500.
2. INTRODUCTION
3. SPECIFICATION
4. OPERATION
5. MAINTENANCE
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Original Language Version © Jack Sealey Limited