Sealey AB1008 - Manual (Page 2)

our range of paraffin / kerosene / diesel heaters represents
excellent value. Workshop tried and tested. All models have an
adjustable thermostat (c°) that cuts in as desired temperature is
reached. Models are fitted with digital room temperature (c°)
display, spare parts storage compartment and heavy duty
pneumatic wheels. Proven pump systems handle either paraffin,
kerosene or diesel with no adjustment of air compressor required.
All models are fitted with fuel tank gauge and heavy-duty filler cap.
sealey Advantages
• PARAFFIN, KEROSENE OR DIESEL - The Sealey AB heaters
will operate on all.
• CLEAN BURNING - A specially designed burner head in a
stainless steel combustion chamber ensures a more thorough
burn of fuel which means greater fuel economy and maximum
heating effect.
• FILTER PROTECTION - The compressor unit is protected by
extra large filter elements.
• LARGE FUEL TANK - The AB series heaters will operate for
between 8 and 11 hours on a single fill of fuel.
• SAFETY FEATURES - The AB series heaters are fitted with a
flame-out device which cuts the fuel supply when the flame is
inadvertently extinguished.
• QUALITY - Manufactured to comply with the rigorous standards.
• AFTER SALES SERVICE - The best after sales service in the
business. full spares back up for all models.
2. INTROdUCTION & SPECIFICATIONS
3. ASSEMBLY
unpack the heater and check contents. should there
be any damaged or missing parts contact your sealey
Dealer immediately.
3.1 slide axle through wheel support frame, slide a bushing
and flat washer (A) to each end of the axle.
3.2 Install wheels with valve stem on the outside, slide flat
washer (B) onto the axle and then using a cotter pin
bend the legs of the pin with pliers to secure. snap on
the wheel caps onto the flat washer (B).
3.3 Place heater on wheel support frame ensuring that the
air inlet is by the wheels and place the heater
onto the frame lining up the holes on the fuel tank
flange with holes on the wheel support frame.
3.4 Place handle on fuel tank flange and line up with the
wheel support frame fixing holes. Insert bolts through
the fuel tank flange and both frames and secure finger
tight only with nuts and washers.
3.5 repeat with process with the rear handle.
3.6 Attach the cord wraps onto the front and rear handles as
shown in fig.1 using screws and nuts.
3.7 When assembly is complete, securely tighten all nuts.

WARNING! dO NOT use the heater without the support
frame fully assembled.
Model
AB1008 /
AB1008SS
AB1258
AB1758 /
AB1758SS
AB2158
rating Btu/hr (kW) 100000 (29.3) 125000 (36.6) 175000 (51.3) 215000 (63)
fuel
Paraffin/
Kerosene/Diesel
Paraffin/
Kerosene/Diesel
Paraffin/
Kerosene/Diesel
Paraffin/Kerosene/
Diesel
fuel tank capacity (Litres) 38 38 49 49
fuel consumption (L/hr) 3.5 3.8 5.2 6.1
Maximum operating Hours 11 10 9.5 8
Pump Pressure (Psi) +/- 10% 4.5 4.5 6.5 8
Voltage/Amp 230V/5A 230V/5A 230V/5A 230V/5A
Air flow (cfm) 520 540 630 670
Heated Volume (m 3 ) 566 702 974 1200
Phase single single single single
Power cable (m) 2.1 2.1 2.1 2.1
size (cm) 99 x 58.5 x 66 99 x 58.5 x 66 109 x 61 x 66 109 x 61 x 66
net Weight (Kg) 23 23 26.3 27.7
fig.1
Assembly Parts
1 Wheel support frame
1 Axle
2 Wheels
1 front Handle
1 rear Handle
2 cord Wraps
2 cotter Pins
4 Axle flat Washers
2 Axle Bushings
2 Wheel caps
4 cord Wrap screws
8 frame Bolts
8 frame nuts
WARNING! This heater is not suitable for use with Bio-Diesel; use of
Bio-Diesel will damage the filter and seals.
Damage caused by use of Bio-Diesel will not be covered by warranty.
AB1008.V2, AB1008ss, AB1258.V2,
AB1758.V2, AB1758ss, AB2158.V2
Issue:4(I)- 12/09/13
Original Language Version
Minimum Clearances from Combustibles
top 1.2m
sides 1.2m
front 2.4m
© Jack sealey Limited