Extron electronic MTP R 15HD RSA D User Manual
Specifications — mtp r 15hd rsa d
Specifications — MTP R 15HD RSA D
1
Extron MTP R 15HD RSA D Mini Twisted Pair Receiver • Specifications
Video
Gain ������������������������������������������������� Unity
Number/signal type ��������������������� 1 set of proprietary analog signals
Connectors ������������������������������������� 1 female RJ-45 on a pigtail
Video input — See MTP Series Transmitters' video output specifications
Video output
Number/signal type ��������������������� 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video,
component video, S-video, or composite video
Connectors ������������������������������������� 1 female 15-pin HD
Nominal level �������������������������������� 1 Vp-p for Y of component video and S-video, and for composite video
0�7 Vp-p for RGB and for R-Y and B-Y of component video
0�3 Vp-p for C of S-video
Minimum/maximum levels �������� 0�3 V to 1�45 Vp-p
Impedance �������������������������������������� 75 ohms
Return loss �������������������������������������� <-30 dB @ 5 MHz
DC offset ����������������������������������������� <±20 mV with input at 0 offset
Maximum resolution �������������������� 1920x1200
N
Refer to the user's manual for the maximum distances recommended for specific resolutions.
Sync
Output type ������������������������������������ RGBHV, RGBS, RGsB, RsGsBs
Standards ���������������������������������������� NTSC 3�58, NTSC 4�43, PAL, SECAM
Output level ����������������������������������� 4�0 V to 5�0 Vp-p, unterminated
Output impedance ������������������������ 110 ohms
Polarity�������������������������������������������� Positive or negative (switch selectable)
Audio
Number/signal type ��������������������� 1 set of proprietary analog signals from an MTP transmitter
Connector ��������������������������������������� 1 female RJ-45
Gain ������������������������������������������������� Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response ���������������������� 20 Hz to 20 kHz, ±1 dB
THD + Noise ���������������������������������� 0�15% @ 1 kHz, 0�3% @ 20 kHz at nominal level
S/N �������������������������������������������������� >70 dB at maximum output (unweighted)
CMRR ���������������������������������������������� >43 dB @ 20 Hz to 20 kHz
Audio output
Number/signal type ��������������������� 1 mono, balanced/unbalanced
Connector ��������������������������������������� (1) 3�5 mm captive screw connector, 5 pole (uses 3 poles)
Impedance �������������������������������������� 50 ohms balanced, 100 ohms balanced
Gain error ��������������������������������������� ±1 dB channel to channel
Nominal level �������������������������������� +4 dBu (1�23 Vrms), -10 dBV (316 mVrms)
Maximum level ������������������������������ 14 dBm, unbalanced at 1% THD+N
Control/remote — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output � 1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input � RS-232 via 3 poles of a 3�5 mm captive screw connector, 5 pole
N
The serial communications link is unidirectional only, transmitter to receiver, unless the receiver's
directional DIP switch has been repositioned. The switch should be repositioned only when the
receiver is the only one in the system.