Powerplus POW8131 TELESCOPIC MITRE SAW 1500W 210MM EN - Manual (Page 8)

POW8131
EN
Copyright © 2010 VARO P a g e | 8 www.varo.com
§ Finally, check the position of the angle indicator. If necessary, release the pointer with a
crosstip screwdriver, move to the 0° position of the angle scale (15) and retighten the
holding screw.
10.3 Making 90° crosscuts with turntable at 0° - 45° (Fig. 6)
§ With POW8131 you can make right and left angular cuts from 0° - 45° to the stop rail.
§ Use the handle (2) to set the turntable (8) to the desired angle i.e. the scale pointer (11) on
the turntable must coincide with the desired angular setting (12) on the stationary base
plate (9).
§ Re-tighten the locking handle (10) to lock the turntable (8) into place.
§ Cut as described under section10.2.
10.4 Mitre cuts 0°-45° and rotary table 0° (Fig. 4/7)
§ The POW8131 can be used to make mitre cuts of 0°-45° relative to the machine bed on
the left side.
§ Lift the machine head (4) to its top position.
§ Fix the rotary table (8) in 0° position.
§ Undo the locking nut (13) and, holding the handle (2), tilt the machine head (4) to the left
until the pointer (23) coincides with the required angle dimension (15).
§ Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
10.5 Precision adjustment of the stop for 45° mitre cuts (Fig. 2/4/8)
§ Lower the machine head (4) and fix with the lock pin (16).
§ Fix the rotary table (8) in 0° position.
§ Undo the locking nut (13) and, holding the handle (2), tilt the machine head (4) to the left
by 45°
§ Place the 45° stop angle (b) between the saw blade (5) and the rotary table (8).
§ Slacken the counter nut and adjust the setting screw (22) until the angle between the saw
(5) and the rotary table (8) equals exactly 45°.
§ Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
10.6 Mitre cuts 0-45 and rotary table 0°-45° (Fig. 4/9)
§ The POW8131 can be used to make mitre cuts on the left at an angle of 0°-45° relative to
the work top and 0°-45° relative to the stop rail.
§ Lift the machine head (4) to its top position.
§ Release the turntable (8) by loosening the locking grip (10).
§ Adjust the rotary table (8) by its handle (2) to the required angle (see also Section 7.4).
§ Re-tighten the locking handle (10) to fix the rotary table in position.
§ Undo the clamping nut (13) and, holding the handle (2), tilt the machine head (4) to the left
to the required angle dimension
§ (see also Section 10.5).
§ Re-tighten the locking nut (13) and make the cut as described in Section 10.2.
11 CHIP EXTRACTION (FIG. 1)
The saw is equipped with a chip collection bag (24). The chip bag (24) can be emptied by
opening the zip fastener at the bottom.
12 REPLACING THE SAW BLADE (FIG. 11)
§ Pull out the power plug.
§ Swing up the machine head (4).
§ Press the lever and swing up the saw blade guard to the point where the recess in the saw
blade guard is above the flange bolt.
§ Press the saw shaft lock (17) with one hand while holding the wrench (31) on the flange
bolt with the other.