Yaskawa AC Drive Z1000 HVAC - Manual (Page 53)

No. Name
User
Setting
o4-11 U2, U3 Initialize Selection
o4-12 kWh Monitor Initialization
o4-13 Number of Run Commands Counter Initialization
o4-17 Real Time Clock Setting
S1-01 Stillness Control Selection
S1-02 Voltage Reduction Rate
S1-03 Voltage Restoration Level
S1-04 Voltage Restoration Complete Level
S1-05 Voltage Restoration Sensitivity Time Constant
S1-06 Voltage Restoration Time Constant at Impact
S2-01 Sequence Timer 1 Start Time
S2-02 Sequence Timer 1 Stop Time
S2-03 Sequence Timer 1 Day Selection
S2-04 Sequence Timer 1 Selection
S2-05 Sequence Timer 1 Reference Source
S2-06 Sequence Timer 2 Start Time
S2-07 Sequence Timer 2 Stop Time
S2-08 Sequence Timer 2 Day Selection
S2-09 Sequence Timer 2 Selection
S2-10 Sequence Timer 2 Reference Source
S2-11 Sequence Timer 3 Start Time
S2-12 Sequence Timer 3 Stop Time
S2-13 Sequence Timer 3 Day Selection
S2-14 Sequence Timer 3 Selection
S2-15 Sequence Timer 3 Reference Source
S2-16 Sequence Timer 4 Start Time
S2-17 Sequence Timer 4 Stop Time
S2-18 Sequence Timer 4 Day Selection
S2-19 Sequence Timer 4 Selection
S2-20 Sequence Timer 4 Reference Source
S3-01
Secondary PI Enable Selection
S3-02
Secondary PI User Display
S3-03
Secondary PI Display Digits
S3-04
Secondary PI Unit Selection
S3-05
Secondary PI Setpoint Value
S3-06
Secondary PI Proportional Gain Setting
S3-07
Secondary PI Integral Time Setting
S3-08
Secondary PI Integral Limit Setting
S3-09
Secondary PI Output Upper Limit
No. Name
User
Setting
S3-10
Secondary PI Output Lower Limit
S3-11
Secondary PI Output Level Selection
S3-12
Secondary PI Disable Mode
S3-13
Secondary PI Low Feedback Detection Level
S3-14
Secondary PI Low Feedback Detection Time
S3-15
Secondary PI High Feedback Level
S3-16
Secondary PI High Feedback Detection Time
S3-17
Secondary PI Feedback Detection Selection
S4-01
BP Auto Transfer on Fault Enable
S4-02
BP Energy Save Bypass Trigger Level
S4-03
BP Energy Save Bypass Timer
S4-04
BP Energy Save Bypass Speed Increase
S5-01 HAND Frequency Reference Selection
S5-02 HAND/AUTO During Run Selection
S5-03
HAND Mode PI Selection
S5-04 HAND Mode Behavior Selection
S5-05
HAND Frequency Reference 1
S5-07 HAND Key Function Selection (HOA Keypad)
S6-01 Emergency Override Speed
S6-02 Emergency Override Reference Selection
S6-03 ov2 Detect Time
S6-04
Main Contactor and Cooling Fan Power Supply
Failure
S7-01 oH1 Detection Selection for Cooling Fan Failure
S7-02
Carrier Frequency Reduction Rate during oH Pre-
Alarm
T1-01 Auto-Tuning Mode Selection
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Base Frequency
T1-06 Number of Motor Poles
T1-07 Motor Base Speed
T1-11 Motor Iron Loss
T2-01 PM Motor Auto-Tuning Mode Selection
i.6 European Standards
YASKAWA ELECTRIC TOEP YAIZ1U 01A YASKAWA AC Drive – Z1000 Safety Precautions 53