SMA SUNNY HOME MANAGER Quick Reference Guide - Manual

HoMan-IS-en-13 | Version 1.3 ENGLISH
2
3 4
super,
Validity
This document is valid for device type "HM-BT-10.GR2" (Sunny Home Manager) from software package 1.10.
You can find the latest version of this document, matching the current software version of the products, at
www.SMA-Solar.com.
Target Group
This document is intended for qualified persons. Only persons with the appropriate skills are allowed to perform
the activities described in this document. Qualified persons must have the following skills:
• Training in the installation and commissioning of electrical devices
• Knowledge of all applicable standards and directives
Intended Use
The Sunny Home Manager is a device for monitoring PV systems and controlling loads in households with
PV systems. The Sunny Home Manager carries out the following basic tasks:
• Readout of energy meter data and data from SMA devices with BLUETOOTH or Speedwire communication
interface
• Transmission of the data to Sunny Portal
• Support for increasing the self-consumption quota
• Limitation of active power feed-in
The product is designed for indoor use only.
The Sunny Home Manager must only be used together with supported devices (for list of supported devices,
see Sunny Home Manager installation manual on the CD provided). For safety reasons, it is not permitted to
modify the product or install components that are not explicitly recommended or distributed by
SMA Solar Technology AG for this product.
Only use this product in accordance with the enclosed documentation and with the local standards and directives.
Any other use can result in personal injury or property damage.
Do not use the Sunny Home Manager in systems which include a Sunny WebBox.
The enclosed documentation is an integral part of this product. Keep the documentation in a convenient place for
future reference and observe all instructions contained therein.
Declaration of Conformity
SMA Solar Technology AG hereby declares that the equipment described is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. The entire EC Declaration of Conformity can
be found at www.SMA-Solar.com.
1 INFORMATION ON THIS DOCUMENT
2 SAFETY
%"/(&3
Danger to life due to electric shock
Lethal voltages are present in the conductive parts of the plug-in power supply and of the top-hat rail power
supply.
• Only use the Sunny Home Manager indoors and in a dry environment; keep it away from liquids.
• Do not open the plug-in power supply.
For commissioning, you will need the following items from the package:
☐ 1 x Sunny Home Manager
☐ 1 x plug-in power supply
☐ 1 x network cable
☐ 2 x screw
☐ 2 x screw anchor
☐ 6 x label
☐ 3 x 4-pole plug
If you are using an SMA Energy Meter in your Sunny Home Manager system, you will need the following
additional material (not included in the scope of delivery):
☐ 1 x network cable
If you wish to connect the Sunny Home Manager to an energy meter with S0 interface, you will need the following
additional material (not included in the scope of delivery):
☐ Per energy meter 1 x cable with at least 2 insulated conductors, core cross-section: 0.2 mm² to 1.5 mm²,
maximum cable length: 30 m
If you wish to connect the Sunny Home Manager to an energy meter with D0 interface, you will need the following
additional material (not included in the scope of delivery):
☐ Per energy meter 1 x cable with optical probe and 4-pole plug
1. Determine the mounting location for the Sunny Home Manager. Bear in mind the requirements for the
mounting location (see Sunny Home Manager installation manual on the CD provided).
2. Mount the Sunny Home Manager on the wall using the screws and screw anchors (distance between drill
holes: 58 mm).
3. Note the serial numbers of all SMA devices with BLUETOOTH or Speedwire interface. For each
SMA radio-controlled socket, also note the load to be assigned to the particular socket. This will facilitate
the registration of your system in Sunny Portal.
$"65*0/
Risk of injury due to incorrect cable routing
Incorrectly routed cables may cause a tripping hazard.
• Ensure that the cables are routed so that no one can step on or trip over them.
/05*$&
Damage to the Sunny Home Manager due to moisture penetration
The Sunny Home Manager is not splash-proof.
• Only use the Sunny Home Manager indoors and in a dry environment.
3 REQUIRED MATERIAL
4 PREPARATION
Device Serial number
Connecting the SMA Energy Meter
• Connect the SMA Energy Meter and the Sunny Home Manager to the same router in the local network.
Connecting Energy Meters with S0 Interface or D0 Interface
You can connect up to three energy meters with S0 interface or D0 interface to the Sunny Home Manager.
Depending on the interface of the particular energy meter, connection to the Sunny Home Manager will differ.
Connecting Energy Meter with D0 Interface
1. Position the magnet retainer of the optical probe at the front upper
right-hand corner of the energy meter. The infrared interfaces on the optical
probe and on the energy meter must be perfectly aligned.
2. Connect the four-pole plug of the optical probe to the pin connector
assigned to the given energy meter. Insert the plug into the upper pin row:
3. Use the labels provided to mark each cable with the pin connector and energy meter to which it is assigned.
5 CONNECTING ENERGY METERS
Requirements for energy meters
The energy meters must comply with the requirements (see Sunny Home Manager installation manual
on the CD provided). A list of recommended energy meters can be found at www.SMA-Solar.com.
Energy meter Pin connector
Purchased electricity meter, bidirectional meter
for feed-in and purchased electricity Meter 1
Feed-in meter Meter 2
PV production meter Meter 3
Device Serial number
gentum des Messstellenbetreibers
Eigen tum d es M essste llenbe treibe rs
Quick Reference Guide for Commissioning
SUNNY HOME MANAGER