ShoreLand'r SRV58TBBAL V.2 - Manual (Page 7)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com
0003249
Page 7 REV E 01/21/08
ITEM PART # DESCRIPTION QTY NOTE
1 4279 SHIM PAD U BOLT 12GA FRAME 4
2 62386 ROCKER ASSEMBLY 2
3 62392 TANDEM BOGIE 2X5 2
4 68358 AXLE DISC BRAKES 80 WIDE NO PAD 2
5 68610 SPRING BRKT BUSHING PLATED ZYU 4
6 68614 SPRING CLAMP 1/4X1 1/2X4 ZYU 4
7 68616 SPRING AND AXLE U-BOLT PLATE 4
8 69011 FENDER ASSY - TANDEM POLY 2
9 69278 TANDEM SPRING MTG BRKT WMENT LEFT 1
10 69279 TANDEM SPRING MTG BRKT WMENT RIGHT 1
11 0110170 HH 9/16-18 X 3 1/4 CS GR5 8
12 0110282 HH 3/4-10 X 4 1/2 CS GR5 2
13 0140040 HH 3/8-16 X 1 CS GR5 8
14 0310170 SUB 1/2 X 2 5/16 X 6 1/2 8
15 0310280 SUB 1/2 X 2 9/16 X 7 5/8 4
16 0730103 SCREW #10-32 X 1 MACHINE 4
17 1310170 WASHER#10 USS FLAT 4
18 1340095 WASHER USS FLAT 3/8 8
19 1410235 HEX LUGNUT 1/2-20 13/16 OD Z&U 20
20 1430550 NUT KEP #10-32 ZP 4
21 1440101 HEX LOCKNUT FLANGE 3/8-16 W/T&T 8
22 1440102 HEX LOCKNUT FLANGE 1/2-13 W/T&T 24
23 1440259 HEX LOCKNUT 9/16-18 GRA 8
24 1440319 HEX NUT 3/4-16 UNF 2
25 3510158 PLASTIC DRIVE RIVOT 4
26 3510253 LIGHT BEZEL - AMBER 2
27 3510363 FENDER STEP PAD TREAD TAPE 2
28 3510364 FENDER STEP PAD TREAD TAPE 2
29 3510597 GROMMET 13/16IN WITH SPLIT 9/16ID 2
30 3610050 BUSHING 3/4 IDX1 ODX1 1/2 BRONZE 2
31 3620211 ZERK 1/4-28 STRAIGHT GREASE 2
32 4510656 CLAMP METAL 3/8 DIA. W/RUBBER#25106 4
33 4610048 SPRING 5 LEAF HOOK 4
34 4811334 DECAL GREASE ZERK ARROW 2
35 5110100 METAL FRAME CLIP - SMALL 2
36 5110572 MARINE YELLOW CLEARANCE LIGHT 2
Dealer / Distributor:
Remove all parts banded or taped to the frame assembly.
Locate the bulk hardware and sort according to size.
Tongue:
Slide tongue into the tongue cap on the front of the
trailer, align holes and insert ½” x 4” hex bolt through
the tongue cap and secure with ½” flange lock nut.
Pull wires from the rear of tongue and feed them thru the tongue
cover, slide the tongue cover over the brake line tube that ex-
tends from the rear of tongue. Align the hole in the tongue cov-
er, the tongue, and the frame cap insert a ½” x 1-½” hex bolt and
secure with a ½” flat washer and a ½” flange lock nut.
Plug harnesses from the tongue into the matching color har-
ness that extends from each side frame; slide the excess
wire back into the tongue. Very carefully form the brake lines
that extends from the tongue and right side frame until they
are aligned. Remove the plug and cap and screw the two
together. Tighten line securely.
Safety Chains:
Take a ½” x 5” hex bolt slide on a ½” flat washer and one
(1) of the safety chains; insert the bolt into the hole on the
actuator housing through tongue and out other side. Place
the second safety chain on the bolt followed with a ½” flat
washer and secure with a ½” flange lock nut.
Bunk Assembly:
Place the pre-assembled bunks on the preset bunk brackets
and secure with a 3/8” x 1” hex bolt and secure with a 3/8”
flange lock nut. Repeat at each bunk bracket location.
Rockers:
Remove all parts from bag, insert the bushings into the hole
and slide the rocker into the center bracket on the spring
bracket, making sure that the grease zerk points toward the
ground, insert a ¾” x 4 ½” hex bolt from the outside in. Se-
cure with a ¾” lock nut. Repeat process on other side.
Springs/axles:
Mount springs on axle by aligning the stub bolt on the leaf
springs with the hole in the center of the spring pad on
the axle, place a spring clamp on top of the leaf spring.
Slide two (2) ½” x 2-5/16” x 6-½” square u-bolts over the
springs and spring clamp, slide a spring/axle u-bolt pad
over the threaded ends of the u-bolts and secure with ½”
flange lock nuts. Repeat on other side of axle and on other
axle.
Place axle with the brakes to the rear of the trailer, slide a
spring bushing into the rear loop on the spring bracket and
insert a 9/16” x 3-¼” hex bolt from the outside in and secure
with a 9/16” lock nut. Repeat on other side of trailer. Slide
the hook end of the spring over the bushing and swing the
axle up so the hole in the front of the leaf spring aligns with
the rear hole in the rocker, insert 9/16” x 3-¼” hex bolt and