ShoreLand'r SRV46TB V.2 User Manual

Page 8

Midwest Industries, Inc.

Ida Grove, IA 51445

800.859.3028

www.shorelandr.com

0003243

Page 8

REV B 4/24/06

Dealer / Distributor:

Remove all parts banded or taped to the frame

assembly. Locate the bulk hardware and sort ac-

cording to size.

Tongue:

Slide tongue into the tongue cap on the front of the

trailer, align holes and insert ½” x 4” hex bolt through

the through tongue cap and secure with ½” ﬂange

lock nut.

Pull wires from the rear of tongue and feed them thru

the tongue cover, slide the tongue cover over the

brake line tube that extends from the rear of tongue.

Align the hole in the tongue cover, the tongue, and

the frame cap insert a ½” x 1-½” hex bolt and secure

with a ½” ﬂat washer and a ½” ﬂange lock nut.

Plug harnesses from the tongue into the matching

color harness that extends from each side frame;

slide the excess wire back into the tongue. Very

carefully form the brake lines that extends from the

tongue and right side frame until they are aligned

remove the plug and cap and screw the two to-

gether. Tighten line securely.

Safety Chains:

Take a ½” x 5” hex bolt slide on a ½” ﬂat washer

and one (1) of the safety chains; insert the bolt into

the hole on the actuator housing through tongue

and out other side. Place the second safety chain

on the bolt followed with a ½” ﬂat washer and se-

cure with a ½” ﬂange lock nut.

Bunk Assembly:

Place the pre-assembled bunks on the preset bunk

brackets and secure with a 3/8” x 1” hex bolt and

secure with a 3/8” ﬂange lock nut. Repeat at each

bunk bracket location.

Rockers:

Remove all parts from bag, insert the bushings

into the hole and slide the rocker into the center

bracket on the spring bracket, making sure that

the grease zerk points toward the ground, insert a

¾” x 4 ½” hex bolt from the outside in. Secure with

a ¾” lock nut. Repeat process on other side.

Springs/axles:

Mount springs on axle by aligning the stub bolt on

the leaf springs with the hole in the center of the

spring pad on the axle, place a spring clamp on top

of the leaf spring. Slide two (2) ½” x 2-5/16” x 6-½”

square u-bolts over the springs and spring clamp,

slide a spring/axle u-bolt pad over the threaded

ends of the u-bolts and secure with ½” ﬂange lock

nuts. Repeat on other side of axle and on other

axle.

Place axle with the brakes to the rear of the trailer,

slide a spring bushing into the rear loop on the

spring bracket and insert a 9/16” x 3-¼” hex bolt

from the outside in and secure with a 9/16” lock nut.

Repeat on other side of trailer. Slide the hook end

of the spring over the bushing and swing the axle

up so the hole in the front of the leaf spring aligns

with the rear hole in the rocker, insert 9/16” x 3-¼”

hex bolt and secure with 9/16” lock nut. Repeat

on other side. To mount the front non brake axle,

insert a spring bushing into the front of the rocker

and align with the hole, insert a 9/16” x 3-¼” hex

bolt and secure with a 9/16” lock nut. Repeat on

the other side. Swing axle into place so the front

of the leaf spring aligns with the hole in the front

loop on the spring bracket and insert a 9/16” x 3-

¼” hex bolt from the outside in and secure with a

9/16” lock nut. Repeat on other side.

Remove plug from right side caliper and insert

brake hose assembly securely, place the other

end of the hose into the clip on the spring bracket

and secure with the hose clip. Carefully uncoil the

brake line and insert into the hose.