ShoreLand'r LUXR2314LTSH V.1 - Manual (Page 3)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003991
Page 3 REV A 01/06/2009
Plug the tongue wire harness into the frame harnesses by match-
ing colors and ends. Push the extra wire provided either into the
rear of the tongue or else remove the grommets in the side frame
and place the extra wire in the side frame. Replace grommets just
removed.
SAFETY CHAINS
Locate a 1/2” x1 1/4” hex bolt. Slip the bolt through a 1/2” flat wash-
er, then place through the last link of one of the safety chains.
Place the bolt with chain attached through the hole provided in the
bottom front of the tongue. Secure with a ½” flange lock nut. Tight-
en. Repeat on the other side and safety chain.
ASSEMBLY AND MOUNTING INSTRUCTIONS:
JACK ON A PROFILE 2000 WINCH BASE
The Profile 2000 winch base used on the 2” x 4” and 2” x 5” frame
trailers is formed so that the jack can be mounted directly to it elimi-
nating the need for other mounting hardware for attaching the jack
to the tongue. The jack required for mounting does not require the
mounting base or any of the original mounting hardware compo-
nents.
Assemble as follows:
The jack must be mounted to the winch base before it is installed
on the trailer tongue. If the winch base is already mounted on the
tongue, it will have to be removed for the jack installation.
Locate the hardware bag and sort all items by size.
Lay the Profile 2000 winch base on its side so the side that the jack
is going to be mounted on is up.
Place the inside jack spacer on the winch base so the center pro-
trusion fits down into the indent in the winch base.
Position the jack mounting plate so it is centered around the inside
jack spacer just positioned.
Lay the jack retainer plate on top of the jack mounting plate aligning
Insert the two ½” and 1 ¼” carriage bolts into the holes just aligned
in the jack retainer plate and the winch base. Secure in place with
½” lock washers and hex nuts. Tighten.
Once tightened, rotate the jack through its normal pivoting range to
make sure it is free to travel and is not binding up.
If jack pivots, place it on the tongue and secure in place with the
bolts and hardware provided with the trailer. Complete the assem-
bly of the winch head to the winch base. Assembly is complete.
WINCH POST ASSEMBLY
Place the winch post assembly on the tongue in the predetermined
position and secure with 3- ½´x 4 1/2” carriage bolts and hex lock
nuts. Tighten
Note that the winch head can now be rotated either up or down.
Identify the correct hole combination to use to position the bow eye
roller just above the bow eye of your boat. When determined, se-
cure in this position by placing the bushing as shown in Diagram C
inside the winch base so it aligns with the hole just identified for the
proper adjustment. Insert another 1/2” x 4-1/2” hex bolt through the
determined mounting hole in the mounting channel and winch base
making sure the bolt passes through the bushing as well. Secure
with a 1/2” lock nut. Tighten all bolts.
SPRINGS
Position the axle so it is properly aligned with the trailer. Place the
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove parts and sort
by size. Remove all the banded items from the frame.
TONGUE
Install the swing tongue by sliding it in the front of the tongue chan-
nel. Line the holes in the tongue with the holes in the tongue chan-
nel. Install the 1/2” x 4” hex bolt in the front cross hole and secure
with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue. Place it
through the hole provided in the tongue cover plate.
Secure the tongue cover plate in position with the same 1/2” x
1-1/2” hex bolt that secures the back of the tongue to the tongue
channel of the frame. Secure with a 1/2” lock nut. Tighten both bolts
just installed.