beautypg.com

ShoreLand'r PT2030TB User Manual

Tire size & carrying capacity chart, Tongue weight adjustment, Bundles required final assembly instructions

background image

PT2030T B & PT2030T BB

Parts Manual

PT2030T B Pontoon 20’ Tandem Trailer - 3000 lbs.

4 4300181 20.5 X 8 X 10-D Tire/MSilver Rim (or)

4 4300203 20.5 X 8 X 10-D Tire/Galv Rim

1 65762

Brake Kit - W/UFP Actuator - 1st Axle

1 60106--

Pontoon Axle Assy W/Brakes

1 62340

Literature Bag - Trailers

1 64692--

Frame Bundle - PT2030T B

Tire Size & Carrying

Capacity Chart

Tire

Load

Carrying

Size Range

Capacity

20.5 X 8 X 10

D

1330

lb. per/tire

Refer to tire side wall for proper tire pressure.

Tongue Weight Adjustment

Approximate Tongue Weight for Best Towing.

Tongue weight too high, move the axle assembly forward.

Tongue weight too low, move the axle assembly backward.

Tongue weight should be 5% to 7% of the total gross

weight of the boat and trailer combined.

Bundles Required

Final Assembly Instructions

Remove the small parts from the frame by cutting the

bands. Remove the bolt bag and sort all the nuts and bolts

by size.

Springs:

Mount the springs under the axle with the 1/2” X 5” axle u-

bolts from the top down. Install the spring plate under the

axle. Tighten with 1/2” flange lock nuts evenly.

Fenders:

Install the fenders and spring bracket assembly to the side

frame using 1/2” u-bolts (Ref.#12) in the area that would

best provide the proper tongue weight.

Axle:

Place one of the spring bushings (Ref.#61) into the rear of

the spring bracket and secure with a 9/16” X 3-1/4” hex

bolt and 9/16” hex lock nut. Repeat on the other side.

Position the axle under the frame, then hook the spring

loop around the bushing just installed. Raise the axle

assembly up so the front of the springs line up with the

front spring bracket hole. Insert the other two (2) 9/16” X

3-1/4” hex bolts and 9/16” hex lock nuts. Tighten all nuts

and bolts but do not over tighten. Allow the spring room

enough to move.

Mount the tire and rim assemblies using 80-90 ft. lbs. of

torque on the lug nuts using a proper tightening procedure.

Tongue:

Install the 9’ tongue wire and grommet in the tongue.

Install the tongue into the nose cone of the trailer frame.

Secure the tongue plate cover (Ref.#4) and the rear of the

tongue with a 1/2” X 1-1/2” hex bolt, 1/2” flat washer and

1/2” hex lock nut. Secure the tongue into the side of the

frame tongue cap using a 1/2” X 4” hex bolt and 1/2” flange

lock nut. Tighten both bolts. Install the coupler on the

tongue and secure with one (1) 1/2” X 4” and two (2) 1/2” X

1” hex bolts. Tighten using 1/2” flange lock nuts. Do not

overtighten.

Actuator & Safety Chain:

Slide the actuator (Ref.#97) into the actuator housing unit

(Ref.#99) and secure with two (2) pins and snap rings

provided with the actuator. Secure the actuator - housing

unit to the front of the tongue using three (3) ½” X 4” hex

bolts and ½” flange lock nuts. Using a ½” X 5” hex bolt in

the lower right mounting hole on tongue, secure the safety

chain. Place a ½” flat washer on ½” X 5” hex bolt followed

by one safety chain and insert into actuator and tongue.

Place the second safety chain on the bolt followed by a ½”

flat washer and ½” flange lock nut. Tighten.

®

PT2030T BB Pontoon 20’ Tandem Trailer - 3000 lbs.

4 4300181 20.5 X 8 X 10-D Tire/MSilver Rim (or)

4 4300203 20.5 X 8 X 10-D Tire/Galv Rim

1 65762

Brake Kit - W/UFP Actuator - 1st Axle

1 60111

Brake Kit - 2nd Axle

2 60106--

Pontoon Axle Assy W/Brakes

1 62340

Literature Bag - Trailers

1 64693--

Frame Bundle - PT2030T BB

This manual is related to the following products: