ShoreLand'r TA0091 - Manual (Page 2)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003540
Page 2 REV A 10/24/08
The TA0091-03 is supplied with U-bolts that will only fit the 2x3
frame.
Installing the ramps in the following manner will allow for the re-
moval of the ramp from the *left side of the trailer first.
TA0091-03
2ATV and 3ATV Ramp Installation Instructions
Locate the four ramp retainer attachment channels. Note that they
are all identical.
The two ramp retainer attachment channels on the right side of the
trailer will be installed on the front side of the trailer front frame tube
to support the ramp.
Place a 3/8” x 3 7/8” x 3” square U-bolt around the front frame tube
so the legs of the U-bolt are pointing forward. Align the holes in one
of the ramp retainer attachment channels with the U-bolt legs, then
slide into position. Note that this channel is mounted on the front
side of the frame tube. Secure in place with 3/8” hex flange lock
nuts. Position the U-bolt so it is 10 ½” from the outside of the side
frame tube as shown in Diagram A. Tighten in position. Repeat this
process on a second channel. Position this ramp retainer attach-
ment channel so that the center hole in the bracket is 27” from the
center hole in the ramp retainer attachment channel just installed.
Tighten enough only to hold in position until the ramp is installed.
Install the other two ramp retainer attachment channels on the left
side of the trailer to the rear of the front frame tube. This will allow
the ramps to overlap past each other in the middle.
Place a 3/8” x 3 7/8” x 3” square U-bolt around the front frame tube
so the legs of the U-bolt are pointing backward. Align the holes in
one of the ramp retainer attachment channels with the U-bolt legs,
Diagram A
Locking pin must be in place and ramps secured before towing trailer. Ramps must
be used with ShoreLand’r 2ATV & 3ATV only. Use of ramps in other applications
may result in ramp failure, property damage and/or bodily injuries.
4811496
then slide into position. Note that this channel is on the rear side of
the frame tube as shown. Secure in place with 3/8” hex flange lock
nuts. Position the U-bolt so it is 10 ½” from the outside of the side
frame tube as described above for the opposite side of the trailer.
Tighten in position. Repeat this process on a second channel. Posi-
tion this ramp retainer attachment channel so that the center hole in
the bracket is 27” from the center hole in the ramp retainer attach-
ment channel just installed. Tighten enough only to hold in position
until the ramp is installed.
Once all four of the ramp retainer attachment channels are at-
tached to the frame, position the right ramp in the ramp retainer at-
tachment channels. The ramp can either be slid into the end of the
channels or else placed in the approximate position, then rotated
into place.
Align the holes provided in the edge of the ramp with the holes in
the center of the ramp retainer attachment channels as follows:
Place one of the ¼” pins with wire retainer through the aligned
holes in the ramp and the retainer attachment channel positioned
10 ½” from the side of the frame and secure.
Align the hole in the second ramp retainer attachment channel with
the second hole in the ramp. Note that the U-bolt may have to be
loosened so the ramp retainer can be moved either direction to
align the holes. When aligned, insert a second ¼” pin with wire
retainer. Once the pin is inserted, retighten the U-bolt loosened to
adjust for proper hole spacing. The two pins will secure the ramps
in the transport position.
The *right side ramp must always be installed first.
Repeat this process on the second ramp.
*Left and Right side of trailer is indicated by standing at the
rear of the trailer.